Preheat your home before on-peak hours start
Start today
Other popular BlueLink Smart Connect workflows and automations
- Turn on the fan for one hour
- When pressing a button, turn off the system and fan
- When temperature drops below a certain point, start emergency heating
- If the temperature outside drops below a chosen point, set the heat to chosen temperature
- Increase the cooling temperature of your home during on-peak hours
- If the temperature outside rise above a chosen point, set the cool to chosen temperature
- Precool your home before on-peak hours start
- Every day at a certain time, modify the temperature in the room
Useful BlueLink Smart Connect and WeMo Insight Switch integrations
Triggers (If this)
- System Mode ChangeThis trigger fires when the system mode changes
- Switched onThis Trigger fires every time your WeMo Insight Switch is turned on.
- Room Temperature Drops BelowThis trigger fires when the temperature in the room drops below the chosen temperature
- Switched offThis Trigger fires every time your WeMo Insight Switch is turned off.
- Room Temperature Rises AboveThis trigger fires when the temperature in the room rise above the chosen temperature
- Standby mode enteredThis Trigger fires every time your WeMo Insight Switch enters standby mode. The switch enters standby mode when the device attached to it is manually powered off or stops drawing power.
- Room Humidity Drops BelowThis trigger fires when the humidity in the room drops below the specified percentage
- Daily minutes on is longer thanThis Trigger fires when the device attached to your WeMo Insight Switch is turned on longer than the minutes you specify.
- Room Humidity Rises AboveThis trigger fires when the humidity in the room rises above the specified percentage
- Daily cost rises aboveThis Trigger fires when the cost of the device attached to your WeMo Insight Switch rises above the daily value you specify.
- Fan Mode ChangeThis trigger fires when fan mode is changed to the specified value
- Monthly estimated cost rises aboveThis Trigger fires when the estimated cost of the device attached to your WeMo Insight Switch rises above the value you specify.
- Hold Status ChangeThis trigger fires when the hold status of the device is changed to the specified value
- Set Temperature Changes To Above XThis trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
- Set Temperature Changes To Below XThis trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
- Low Remote Sensor BatteryThis trigger fires when the remote sensor battery is low
- Low Thermostat BatteryThis trigger fires when the thermostat battery is low
- Check WarningThis trigger fires when the check warning activates
- UV WarningThis trigger fires when the UV warning activates
- HUMID PADS WarningThis trigger fires when the HUMID PADS warning activates
- Filter WarningThis trigger fires when the filter warning activates
Queries (With)
- History of times Switch entered Standby modeThis query returns a list of times when your WeMo Insight Switch entered standby mode. The switch enters standby mode when the device attached to it was manually powered off or stops drawing power.
- Device StateThis query returns the current state of the selected device
- History of Switched offThis query returns a list of times when your WeMo Insight Switch was turned off.
- On-peak hours intervalThis query returns validated interval for on-peak hours
- History of Switched onThis query returns a list of when your WeMo Insight Switch was turned on.
- History of when WeMo Insight Switch was on longer than a specified timeThis query returns a list of when the WeMo Insight Switch was turned on longer than the specified minutes.
Actions (Then that)
- Change Room TemperatureThis action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
- Turn onThis Action will turn a WeMo Insight Switch on. If the WeMo Insight Switch is already on, it will remain on.
- Change Cool SetpointThis action will change the current cool setpoint of the selected device.
- Turn offThis Action will turn a WeMo Switch off. If the WeMo Switch is already off, it will remain off.
- Change Heat SetpointThis action will change the current heat setpoint of the selected device.
- Turn on then offThis Action will turn a WeMo Insight Switch on then immediately back off.
- Change Hold StatusThis action will change the current hold status of the device (either ENABLED or DISABLED)
- Turn off then onThis Action will turn a WeMo Switch off then immediately back on.
- Change System ModeThis action will change the current running mode of the device
- Toggle on/offThis Action will toggle a WeMo Insight Switch on or off.
- Change Fan ModeThis action will change the current fan mode of the device
- Change Hold ModeThis action will change the current hold mode of the device
IFTTT helps all your apps and devices work better together