If the temperature outside drops below a chosen point, set the heat to chosen temperature
Start today
Other popular BlueLink Smart Connect workflows and automations
- When pressing a button, turn off the system and fan
- Increase the cooling temperature of your home during on-peak hours
- When You Enter an Area Change Room Temperature
- Precool your home before on-peak hours start
- Preheat your home before on-peak hours start
- Decrease the heating temperature of your home during on-peak hours
- When temperature drops below a certain point, start emergency heating
- Every day at a certain time, modify the temperature in the room
Useful BlueLink Smart Connect and WeMo Maker integrations
Triggers (If this)
- System Mode ChangeThis trigger fires when the system mode changes
- Relay onThis Trigger fires every time your WeMo Maker relay is turned on in toggle mode.
- Room Temperature Drops BelowThis trigger fires when the temperature in the room drops below the chosen temperature
- Relay offThis Trigger fires every time your WeMo Maker relay is turned off in toggle mode.
- Room Temperature Rises AboveThis trigger fires when the temperature in the room rise above the chosen temperature
- Momentary onThis Trigger fires every time your WeMo Maker relay is turned on in momentary mode.
- Room Humidity Drops BelowThis trigger fires when the humidity in the room drops below the specified percentage
- Sensor triggeredThis Trigger fires every time a signal is detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.
- Room Humidity Rises AboveThis trigger fires when the humidity in the room rises above the specified percentage
- Sensor not triggeredThis Trigger fires every time a signal is not detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.
- Fan Mode ChangeThis trigger fires when fan mode is changed to the specified value
- Hold Status ChangeThis trigger fires when the hold status of the device is changed to the specified value
- Set Temperature Changes To Above XThis trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
- Set Temperature Changes To Below XThis trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
- Low Remote Sensor BatteryThis trigger fires when the remote sensor battery is low
- Low Thermostat BatteryThis trigger fires when the thermostat battery is low
- Check WarningThis trigger fires when the check warning activates
- UV WarningThis trigger fires when the UV warning activates
- HUMID PADS WarningThis trigger fires when the HUMID PADS warning activates
- Filter WarningThis trigger fires when the filter warning activates
Queries (With)
- History of being turned on in momentary modeThis query returns a list of when your WeMo Maker relay was turned on in momentary mode.
- Device StateThis query returns the current state of the selected device
- History of times a signal was not detected by an enabled sensorThis query returns a list of times a signal was not detected by an enabled sensor.
- On-peak hours intervalThis query returns validated interval for on-peak hours
- History of times a signal was detected by an enabled sensorThis query returns a list of times a signal was detected by an enabled sensor.
- History of relay offsThis query returns a list of when your WeMo Maker relay was turned off in toggle mode.
- History of relay onsThis query returns a list of when your WeMo Maker relay was turned on in toggle mode.
Actions (Then that)
- Turn relay onThis Action will turn your WeMo Maker on. If the WeMo Maker is already on, it will remain on.
- Change Room TemperatureThis action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
- Turn relay offThis Action will turn a WeMo Maker off. If the WeMo Maker is already off, it will remain off.
- Change Cool SetpointThis action will change the current cool setpoint of the selected device.
- Toggle relayThis Action will toggle a Wemo Maker if it is in toggle mode. If the relay is on, it will be turned off and vice versa.
- Change Heat SetpointThis action will change the current heat setpoint of the selected device.
- Turn relay off then onThis Action will turn a Wemo Maker off then on. If the WeMo Maker is already off, it will remain off.
- Change Hold StatusThis action will change the current hold status of the device (either ENABLED or DISABLED)
- Turn relay on then offThis Action will turn a WeMo Maker on then off. If the WeMo Maker is already on, it will be turned off after 2 seconds.
- Change System ModeThis action will change the current running mode of the device
- Turn relay on momentarilyThis Action will turn a WeMo Maker on for 300 milliseconds. Note: WeMo Maker must be in 'Momentary' mode for this action to work.
- Change Fan ModeThis action will change the current fan mode of the device
- Turn relay on momentarily multiple timesThis Action will turn a WeMo Maker on for 300 milliseconds as many times as you set. Note: The WeMo Maker must be in 'Momentary' mode for this Action to work.
- Change Hold ModeThis action will change the current hold mode of the device
- Turn relay on then off multiple timesThis Action will turn relay on then off as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.
- Turn relay off then on multiple timesThis Action will turn relay off then on as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.
IFTTT helps all your apps and devices work better together