Synchronize a HomeSeer virtual device with a product (in this case, a WeMo powered table lamp)
Start today
Other popular HomeSeer workflows and automations
- Homeseer device trigger
- Turn On Device When Connected
- If WiFi disconnects on your Android device, run a HomeSeer Event
- Geofence left home
- Launch HomeSeer Event When Wyze Camera Detects Motion
- Geofence at home
- Notify my family when nobody's at home
- Launch HomeSeer Event When Wyze Motion Sensor Detects Motion
Useful HomeSeer and iZone integrations
Triggers (If this)
- iZone System is OffThis Trigger fires if the iZone system is turned off.
- A device is turned onThis Trigger fires when a device attached to your HomeSeer system is turned on.
- Light is turned onThis trigger fires when an iLight is turned on.
- A device is turned offThis Trigger fires when a device attached to your HomeSeer system is turned off.
- Light is turned offThis trigger fires when an iLight is turned off.
- Switch battery is lowThis trigger fires when one iLight switch battery low alarmed.
- iDrate system is turned onThis trigger fires when your iDrate is turned on.
- iZone system duct temperature rises aboveThis Trigger fires if the A/C systems supply air temperature rises above a specified threshold.
- iZone system duct temperature falls belowThis Trigger fires if the iZone systems supply air temperature falls below a specified threshold.
- iDrate system is turned offThis trigger fires when your iDrate is turned off.
- Zone temperature rises aboveThis Trigger fires when a zone's actual temperature rises above a specified threshold.
- iDrate controller fault detectedThis trigger fires when an iDrate controller detects a fault.
- iDrate station fault detectedThis trigger fires when an iDrate Station detects a fault.
- Zone temperature falls belowThis Trigger fires when a zone's actual temperature falls below a specified threshold.
- iZone system temperature rises aboveThis Trigger fires when the AC unit temperature rises above a specified threshold.
- iZone system temperature falls belowThis Trigger fires when the AC unit temperature falls below a specified threshold.
- iZone System is OnThis Trigger fires if the iZone system is turned on.
Queries (With)
- History of iZone system duct temperature falls belowThis query returns a list of if the iZone systems supply air temperature falls below a specified threshold. Note: this query will only return future events after this Applet is created.
- History of a device is turned onThis query returns a list of when a device attached to your HomeSeer system was turned on.
- History of iDrate station fault detectedThis query returns a list of when an iDrate Station detects a fault.
- History of iLight is turned onThis query returns a list of when an iLight was turned on.
- History of iZone system is offThis query returns a list of if the iZone system was turned off.
- History of when the iDrate system turned onThis query returns a list of when your iDrate was turned on.
- History of lights turned offThis query returns a list of when an iLight was turned off.
- History of iZone System is OnThis query returns a list of when the iZone system was turned on.
- History of iZone system temperature rises aboveThis query returns a list of when the AC unit temperature rises above a specified threshold. Note: this query will only return future events after this Applet is created.
Actions (Then that)
- Turn all lights onThis action will turn all iLights on.
- Run a HomeSeer system eventThis Action will run a HomeSeer system event. HomeSeer events can be programmed to control just about any combination of home automation products installed in your home!
- Turn all lights offThis action will turn all iLights off.
- Turn on a deviceThis Action will turn on a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
- Turn light onThis action will turn the specified iLight on.
- Turn off a deviceThis Action will turn off a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
- Turn light offThis action will turn the specified iLight off.
- Dim a deviceThis Action will dim a dimmable lighting device attached to your HomeSeer system.
- Decrease iZone system target temperatureThis Action will decrease the A/C setpoint by the selected number of degrees celcius.
- Lock a door lockThis Action will lock a door lock attached to your HomeSeer system.
- Set light brightnessChange the brightness of an iLight.
- Unlock a door lockThis Action will unlock a door lock attached to your HomeSeer system.
- Set zone modeThis Action will set the selected zone to selected mode
- Change a thermostat's cool set-pointThis Action will change the cool set-point of a thermostat attached to your HomeSeer system.
- Set iSaveThis Action will set iSave for the selected iZone system. The iSave cools your whole home using your ducted reverse cycle air conditioner’s fan mode for only a few cents an hour.
- Change a thermostat's heat set-pointThis Action will change the heat set-point of a thermostat attached to your HomeSeer system.
- Set iZone system target temperatureThis Action will change the iZone A/C system's setpoint temperature.
- Change a thermostat's operating mode to autoThis Action will change the the operating mode of a thermostat attached to your HomeSeer system to auto.
- Increase iZone system target temperatureThis Action will increase the A/C setpoint temperature by selected number of degrees celcius.
- Change a thermostat's operating mode to offThis Action will change the the operating mode of a thermostat attached to your HomeSeer system to off.
- Set zone target temperatureThis Action will change the selected zone setpoint temperature.
- Change a thermostat's operating mode to coolThis Action will change the the operating mode of a thermostat attached to your HomeSeer system to cool.
- Increase zone target temperatureThis Action will increase the selected zone setpoint temperature by the selected number of degrees celcius.
- Change a thermostat's operating mode to heatThis Action will change the the operating mode of a thermostat attached to your HomeSeer system to heat.
- Decrease zone target temperatureThis Action will decrease the selected zone setpoint temperature by the selected number of degrees celcius.
- Send a text command to HomeSeerThis action will send a text command to your HomeSeer system.
- Set light colorThis action will change the colour of the iLight.
- Change light effectThis action will change the special effect for the iLight.
- Activate iZone favouriteThis Action will activate the selected iZone favourite.
- Activate iLight favouriteThis action will activate a specified favourite for your iLight.
- Run iDrate ProgramThis action will run the selected Program on the iDrate.
- Turn iDrate system onThis action will turn the iDrate system on.
- Turn iDrate system offThis action will turn the iDrate system off.
- Set iDrate weather modeThis action will changes the iDrate weather mode to fine.
- Run iDrate stationThis action will run the selected iDrate station.
- Set iDrate run time ratio factorThis action will change the station run times by the selected percentage. This will increase or decrease the programmed station running time.
- Turn on iZone systemThis Action will turn on the iZone system.
- Set iZone system modeThis Action will change the iZone air condition system to the selected mode.
- Set iZone system fan speedThis Action will set the iZone A/C system to the selected fan speed.
- Turn off iZone systemThis Action will turn off the iZone AC system.
- Set iZone system sleep timerThis Action will set the A/C sleep timer to a predetermined period.
IFTTT helps all your apps and devices work better together