Connect Husqvarna Automower® to eWeLink Smart Home and unlock powerful automations

This Trigger fires every time your eWeLink Button is pressed.

This trigger fires when your mower is searching for satellites.

This trigger fires when your eWeLink Support 4-Channel Plug is turned on or off.

This trigger fires when your mower starts to charge.

This trigger fires when your eWeLink Support 3-Channel Plug is turned on or off.

This trigger fires when an error has occurred.

This trigger fires when your eWeLink 2-Channel Plug is turned on or off.

This trigger fires when your mower starts to mow.

This trigger fires when your eWeLink Support 1-Channel Plug is turned on or off.

This trigger fires when your mower has paused.

This trigger fires when your eWeLink Support 4-Channel Switch is turned on or off.

This trigger fires when your mower has stopped.

This trigger fires when your eWeLink 3-Channel Switch is turned on or off.

This trigger fires when your mower has parked.

This trigger fires when your eWeLink Support 2-Channel Switch is turned on or off.

This trigger fires when your mower is leaving the charging station.

This trigger fires when your eWeLink Support 1-Channel Switch is turned on or off.

This trigger fires when your mower's status changes.

This trigger fires when your eWeLink Support Smart Dimmer is turned on or off.

This triggers when your mower starts to go home to the charging station.

This trigger fires when the brightness of selected dimmer is above threshold.

This trigger fires when the brightness of selected dimmer is below threshold.

This trigger fires when the state of selected door sensor is open or closed.

This trigger fires when the temperature of selected device goes above or below threshold.

This trigger fires when the humidity of selected device goes above or below threshold.

This trigger fires when the voltage of selected device is above or below threshold.

This trigger fires when the electric current of the selected device goes above or below threshold.

This trigger fires when your light is turned on or off.

This trigger fires when your light brightness goes above or below.

This trigger fires when the fan or the light of your FanLight is turned on or off

This trigger fires when an alarm of your RF Bridge is activated.

This Trigger fires every time the camera detects a motion event.

This trigger fires when the water level of a diffuser is low.

This trigger fires when motion is detected or no motion is detected from Zigbee motion sensor.

This trigger fires when leak is detected from water leak sensor.

This trigger fires when the status of a Zigbee door sensor is open or closed.

This trigger fires when Zigbee Wireless Switch is pressed, double pressed, or long pressed.

This trigger fires when the selected electric curtain is open or closed.

This trigger fires when the child lock status changes (enabled/disabled).

This trigger fires when the thermostat mode changes.

This trigger fires when the thermostat turns on or off

This trigger fires when your light’s color temperature of light apperances warm or cool white.

This trigger fires when your lights to a specified colour .

This Trigger fires every time your eWeLink Scene Controller is pressed.

This query returns statistics for selected Automower®. Time related values are displayed in hours. A value of -1 indicates that the mower does not support statistics for that value. 

This query returns the on/off state of the device you choose.

Use this query to quickly find out if all your robotic mowers are parked before starting your sprinklers.

With this query you can track where Automower® mowed during the last mowing session.

This action will turn your eWeLink Support 4-Channel Plug on or off.

This action will run your mower for a specified duration after which it will go back to its regular schedule. Automower® will start when the battery is fully loaded. For AIM-capable mowers, you can also start in a specific area that you have created.

This action will turn your eWeLink Support 3-Channel Plug on or off.

This action will send your mower back to the charging station where it will remain parked until manually started.

This action will turn your eWeLink 2-Channel Plug on or off.

This action will set Automower® to run according to its schedule.

This action will turn your eWeLink Support 1-Channel Plug on or off.

This action will pause your mower.

This action will turn your eWeLink 4-Channel Switch on or off.

This action will send your mower back to its charging station, skipping the current mowing session.

This action will turn your eWeLink Support 3-Channel Switch on or off.

This action will park your mower for a specified duration, after which it will resume according to its set schedule.

This action will turn your eWeLink Support 2-Channel Switch on or off.

This action will make Automower® play Happy Birthday.

This action will turn your eWeLink Support 1-Channel Switch on or off.

This action will enable a stay-out zone for your robotic mower, based on the AIM map created in the Automower® Connect application.

This action will turn your eWeLink Support smart dimmer on or off.

This action will disable a stay-out zone for your mower, based on the AIM map created in the Automower® Connect application.

This action will set brightness for selected eWeLink Support smart dimmer .

This action will set the headlights on your Automower® robotic mower to "Always ON".

This action will set a color for selected light.

This action will set the headlights on your Automower® robotic mower to "Always OFF".

This action will set a color temperature for selected light.

This action will set the brightness for selected light .

This action will turn your light on or off.

This action will press selected remote button on your RF Bridge.

This action will turn on or turn off the fan or the light of your fanlight.

This action will open or close your electric curtain.

This action will turn your diffuser on or off.

This action will open selected curtain to the percentage you set.

This action will enable or disable the child lock.

This action will change the thermostat mode (Manual/Program).

This action will turn your eWeLink Thermostat on or off.

This action will set the light on/off or the fan speed of fanlight.

This Action will makes the camera sound an alarm.