Precool your home before on-peak hours start
Start today
Triggers (If this)
Actions (Then that)
Other popular BlueLink Smart Connect workflows and automations
-
-
-
When You Enter an Area Change Room Temperature
-
-
Increase the cooling temperature of your home during on-peak hours
-
-
If the temperature outside drops below a chosen point, set the heat to chosen temperature
-
-
Turn on the fan for one hour
-
-
When pressing a button, turn off the system and fan
1
-
-
Preheat your home before on-peak hours start
-
-
When temperature drops below a certain point, start emergency heating
-
-
If the temperature outside rise above a chosen point, set the cool to chosen temperature
-
Useful BlueLink Smart Connect and Envoy integrations
Triggers (If this)
-
System Mode Change
This trigger fires when the system mode changes
-
Visitor is pre-registered
This Trigger fires every time a visitor is pre-registered.
-
Room Temperature Drops Below
This trigger fires when the temperature in the room drops below the chosen temperature
-
Visitor finishes signing in
This Trigger fires every time a visitor finishes signing in.
-
Room Temperature Rises Above
This trigger fires when the temperature in the room rise above the chosen temperature
-
Visitor signs out
This Trigger fires every time a visitor signs out.
-
Room Humidity Drops Below
This trigger fires when the humidity in the room drops below the specified percentage
-
Room Humidity Rises Above
This trigger fires when the humidity in the room rises above the specified percentage
-
Fan Mode Change
This trigger fires when fan mode is changed to the specified value
-
Hold Status Change
This trigger fires when the hold status of the device is changed to the specified value
-
Set Temperature Changes To Above X
This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
-
Set Temperature Changes To Below X
This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
-
Low Remote Sensor Battery
This trigger fires when the remote sensor battery is low
-
Low Thermostat Battery
This trigger fires when the thermostat battery is low
-
Check Warning
This trigger fires when the check warning activates
-
UV Warning
This trigger fires when the UV warning activates
-
HUMID PADS Warning
This trigger fires when the HUMID PADS warning activates
-
Filter Warning
This trigger fires when the filter warning activates
System Mode Change
This trigger fires when the system mode changes
Visitor is pre-registered
This Trigger fires every time a visitor is pre-registered.
Room Temperature Drops Below
This trigger fires when the temperature in the room drops below the chosen temperature
Visitor finishes signing in
This Trigger fires every time a visitor finishes signing in.
Room Temperature Rises Above
This trigger fires when the temperature in the room rise above the chosen temperature
Visitor signs out
This Trigger fires every time a visitor signs out.
Room Humidity Drops Below
This trigger fires when the humidity in the room drops below the specified percentage
Room Humidity Rises Above
This trigger fires when the humidity in the room rises above the specified percentage
Fan Mode Change
This trigger fires when fan mode is changed to the specified value
Hold Status Change
This trigger fires when the hold status of the device is changed to the specified value
Set Temperature Changes To Above X
This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
Set Temperature Changes To Below X
This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
Low Remote Sensor Battery
This trigger fires when the remote sensor battery is low
Low Thermostat Battery
This trigger fires when the thermostat battery is low
Check Warning
This trigger fires when the check warning activates
UV Warning
This trigger fires when the UV warning activates
HUMID PADS Warning
This trigger fires when the HUMID PADS warning activates
Filter Warning
This trigger fires when the filter warning activates
Queries (With)
Actions (Then that)
-
Change Room Temperature
This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
-
Change Cool Setpoint
This action will change the current cool setpoint of the selected device.
-
Change Heat Setpoint
This action will change the current heat setpoint of the selected device.
-
Change Hold Status
This action will change the current hold status of the device (either ENABLED or DISABLED)
-
Change System Mode
This action will change the current running mode of the device
-
Change Fan Mode
This action will change the current fan mode of the device
-
Change Hold Mode
This action will change the current hold mode of the device
Change Room Temperature
This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
Change Cool Setpoint
This action will change the current cool setpoint of the selected device.
Change Heat Setpoint
This action will change the current heat setpoint of the selected device.
Change Hold Status
This action will change the current hold status of the device (either ENABLED or DISABLED)
Change System Mode
This action will change the current running mode of the device
Change Fan Mode
This action will change the current fan mode of the device
Change Hold Mode
This action will change the current hold mode of the device
IFTTT helps all your apps and devices work better together