Connect BlueLink Smart Connect to go-e Charger and unlock powerful automations

This trigger fires when the system mode changes

This trigger fires when charging has started.

This trigger fires when the temperature in the room drops below the chosen temperature

This trigger fires when the car is plugged in.

This trigger fires when the temperature in the room rise above the chosen temperature

This trigger fires when an Error occurs.

This trigger fires when the humidity in the room drops below the specified percentage

This trigger fires when the charging process has finished.

This trigger fires when the humidity in the room rises above the specified percentage

This trigger fires when charging is paused.

This trigger fires when fan mode is changed to the specified value

This trigger fires when the model status changes.

This trigger fires when the hold status of the device is changed to the specified value

This trigger fires when a transaction happened.

This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you

This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you

This trigger fires when the remote sensor battery is low

This trigger fires when the thermostat battery is low

This trigger fires when the check warning activates

This trigger fires when the UV warning activates

This trigger fires when the HUMID PADS warning activates

This trigger fires when the filter warning activates

This query returns the amount of power from your battery.

This query returns the current state of the selected device

This query returns the ssid of the currently connected WiFi.

This query returns validated interval for on-peak hours

This query returns the friendly name of the charger.

This query returns the variant of the charger.

This query returns the current charger mode.

This query returns the grid frequency.

This query returns the automatic stop energy limit.

This query returns the flexible energy tariff price limit.

This query returns the current card id.

This query returns the total energy charged since purchase.

This query returns the temperature of the connector (type 2) and power supply.

This query returns true if an current limiting adapter (i.e. 16A) is used.

This query returns the load balancing amperes.

This query returns the force state.

This query returns the energy limit for the current charging session.

This query returns the IP address of the charger.

This query returns the firmware version.

This query returns the energy array.

This query returns the colors for Idle, Charging and Done.

This query returns the cable current limit.

This query returns the current model status.

This query returns the effective charging current.

This query returns the amount of power delivered by your pv.

This query returns the current unlock mode.

This query returns the requested current.

This query returns information about a connected WiFi.

This query returns the car state (Unknown, Idle, Wait for Car, Charging, Finished or Error).

This query returns the current state of access control setting.

This query returns the led-ring brightness

This query returns true/false, depending on if the car is allowed to charge right now.

This query returns the amount of power delivered by the power grid.

This query returns the led energy save mode.

This action will set the charging current.

This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.

This action will pause the charging process.

This action will change the current cool setpoint of the selected device.

This action will start the charging process.

This action will change the current heat setpoint of the selected device.

This action will set the charging state to Neutral, Force-Off or Force-On.

This action will change the current hold status of the device (either ENABLED or DISABLED)

This action will reboot the charger.

This action will change the current running mode of the device

This action will set the energy limit for the current charging session.

This action will change the current fan mode of the device

This action will set the mode of the charger.

This action will change the current hold mode of the device

This action will set the ledring brightness.

This action will set the friendly name.

This action will set the colors for Idle, Charging and Done.

This action will set the unlock mode.

This action will set the access control setting.

This action will set the transaction setting.

This action will set the led energy save mode.

This action will set the flexible energy tariff price limit.

This action will set the automatic stop energy.