Connect BlueLink Smart Connect to iZone and unlock powerful automations

This Trigger fires if the iZone system is turned off.

This trigger fires when the system mode changes

This trigger fires when an iLight is turned on.

This trigger fires when the temperature in the room drops below the chosen temperature

This trigger fires when an iLight is turned off.

This trigger fires when the temperature in the room rise above the chosen temperature

This trigger fires when one iLight switch battery low alarmed.

This trigger fires when the humidity in the room drops below the specified percentage

This trigger fires when your iDrate is turned on.

This trigger fires when the humidity in the room rises above the specified percentage

This Trigger fires if the A/C systems supply air temperature rises above a specified threshold.

This trigger fires when fan mode is changed to the specified value

This Trigger fires if the iZone systems supply air temperature falls below a specified threshold.

This trigger fires when the hold status of the device is changed to the specified value

This trigger fires when your iDrate is turned off.

This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you

This Trigger fires when a zone's actual temperature rises above a specified threshold.

This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you

This trigger fires when an iDrate controller detects a fault.

This trigger fires when the remote sensor battery is low

This trigger fires when an iDrate Station detects a fault.

This trigger fires when the thermostat battery is low

This Trigger fires when a zone's actual temperature falls below a specified threshold.

This trigger fires when the check warning activates

This Trigger fires when the AC unit temperature rises above a specified threshold.

This trigger fires when the UV warning activates

This Trigger fires when the AC unit temperature falls below a specified threshold.

This trigger fires when the HUMID PADS warning activates

This Trigger fires if the iZone system is turned on.

This trigger fires when the filter warning activates

This query returns a list of if the iZone systems supply air temperature falls below a specified threshold. Note: this query will only return future events after this Applet is created.

This query returns the current state of the selected device

This query returns a list of when an iDrate Station detects a fault.

This query returns validated interval for on-peak hours

This query returns a list of when an iLight was turned on.

This query returns a list of if the iZone system was turned off.

This query returns a list of when your iDrate was turned on.

This query returns a list of when an iLight was turned off.

This query returns a list of when the iZone system was turned on.

This query returns a list of when the AC unit temperature rises above a specified threshold. Note: this query will only return future events after this Applet is created.

This action will turn all iLights on.

This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.

This action will turn all iLights off.

This action will change the current cool setpoint of the selected device.

This action will turn the specified iLight on.

This action will change the current heat setpoint of the selected device.

This action will turn the specified iLight off.

This action will change the current hold status of the device (either ENABLED or DISABLED)

This Action will decrease the A/C setpoint by the selected number of degrees celcius.

This action will change the current running mode of the device

Change the brightness of an iLight.

This action will change the current fan mode of the device

This Action will set the selected zone to selected mode

This action will change the current hold mode of the device

This Action will set iSave for the selected iZone system. The iSave cools your whole home using your ducted reverse cycle air conditioner’s fan mode for only a few cents an hour.

This Action will change the iZone A/C system's setpoint temperature.

This Action will increase the A/C setpoint temperature by selected number of degrees celcius.

This Action will change the selected zone setpoint temperature.

This Action will increase the selected zone setpoint temperature by the selected number of degrees celcius.

This Action will decrease the selected zone setpoint temperature by the selected number of degrees celcius.

This action will change the colour of the iLight.

This action will change the special effect for the iLight.

This Action will activate the selected iZone favourite.

This action will activate a specified favourite for your iLight.

This action will run the selected Program on the iDrate.

This action will turn the iDrate system on.

This action will turn the iDrate system off.

This action will changes the iDrate weather mode to fine.

This action will run the selected iDrate station.

This action will change the station run times by the selected percentage. This will increase or decrease the programmed station running time.

This Action will turn on the iZone system.

This Action will change the iZone air condition system to the selected mode.

This Action will set the iZone A/C system to the selected fan speed.

This Action will turn off the iZone AC system.

This Action will set the A/C sleep timer to a predetermined period.