Connect eWeLink Smart Home to WeMo Maker and unlock powerful automations

This Trigger fires every time your eWeLink Button is pressed.

This Trigger fires every time your WeMo Maker relay is turned on in toggle mode.

This trigger fires when your eWeLink Support 4-Channel Plug is turned on or off.

This Trigger fires every time your WeMo Maker relay is turned off in toggle mode.

This trigger fires when your eWeLink Support 3-Channel Plug is turned on or off.

This Trigger fires every time your WeMo Maker relay is turned on in momentary mode.

This trigger fires when your eWeLink 2-Channel Plug is turned on or off.

This Trigger fires every time a signal is detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.

This trigger fires when your eWeLink Support 1-Channel Plug is turned on or off.

This Trigger fires every time a signal is not detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.

This trigger fires when your eWeLink Support 4-Channel Switch is turned on or off.

This trigger fires when your eWeLink 3-Channel Switch is turned on or off.

This trigger fires when your eWeLink Support 2-Channel Switch is turned on or off.

This trigger fires when your eWeLink Support 1-Channel Switch is turned on or off.

This trigger fires when your eWeLink Support Smart Dimmer is turned on or off.

This trigger fires when the brightness of selected dimmer is above threshold.

This trigger fires when the brightness of selected dimmer is below threshold.

This trigger fires when the state of selected door sensor is open or closed.

This trigger fires when the temperature of selected device goes above or below threshold.

This trigger fires when the humidity of selected device goes above or below threshold.

This trigger fires when the voltage of selected device is above or below threshold.

This trigger fires when the electric current of the selected device goes above or below threshold.

This trigger fires when your light is turned on or off.

This trigger fires when your light brightness goes above or below.

This trigger fires when the fan or the light of your FanLight is turned on or off

This trigger fires when an alarm of your RF Bridge is activated.

This Trigger fires every time the camera detects a motion event.

This trigger fires when the water level of a diffuser is low.

This trigger fires when motion is detected or no motion is detected from Zigbee motion sensor.

This trigger fires when leak is detected from water leak sensor.

This trigger fires when the status of a Zigbee door sensor is open or closed.

This trigger fires when Zigbee Wireless Switch is pressed, double pressed, or long pressed.

This trigger fires when the selected electric curtain is open or closed.

This trigger fires when the child lock status changes (enabled/disabled).

This trigger fires when the thermostat mode changes.

This trigger fires when the thermostat turns on or off

This trigger fires when your light’s color temperature of light apperances warm or cool white.

This trigger fires when your lights to a specified colour .

This Trigger fires every time your eWeLink Scene Controller is pressed.

This query returns a list of when your WeMo Maker relay was turned on in momentary mode.

This query returns the on/off state of the device you choose.

This query returns a list of times a signal was not detected by an enabled sensor.

This query returns a list of times a signal was detected by an enabled sensor.

This query returns a list of when your WeMo Maker relay was turned off in toggle mode.

This query returns a list of when your WeMo Maker relay was turned on in toggle mode.

This action will turn your eWeLink Support 4-Channel Plug on or off.

This Action will turn your WeMo Maker on. If the WeMo Maker is already on, it will remain on.

This action will turn your eWeLink Support 3-Channel Plug on or off.

This Action will turn a WeMo Maker off. If the WeMo Maker is already off, it will remain off.

This action will turn your eWeLink 2-Channel Plug on or off.

This Action will toggle a Wemo Maker if it is in toggle mode. If the relay is on, it will be turned off and vice versa.

This action will turn your eWeLink Support 1-Channel Plug on or off.

This Action will turn a Wemo Maker off then on. If the WeMo Maker is already off, it will remain off.

This action will turn your eWeLink 4-Channel Switch on or off.

This Action will turn a WeMo Maker on then off. If the WeMo Maker is already on, it will be turned off after 2 seconds.

This action will turn your eWeLink Support 3-Channel Switch on or off.

This Action will turn a WeMo Maker on for 300 milliseconds. Note: WeMo Maker must be in 'Momentary' mode for this action to work.

This action will turn your eWeLink Support 2-Channel Switch on or off.

This Action will turn a WeMo Maker on for 300 milliseconds as many times as you set. Note: The WeMo Maker must be in 'Momentary' mode for this Action to work.

This action will turn your eWeLink Support 1-Channel Switch on or off.

This Action will turn relay on then off as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.

This action will turn your eWeLink Support smart dimmer on or off.

This Action will turn relay off then on as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.

This action will set brightness for selected eWeLink Support smart dimmer .

This action will set a color for selected light.

This action will set a color temperature for selected light.

This action will set the brightness for selected light .

This action will turn your light on or off.

This action will press selected remote button on your RF Bridge.

This action will turn on or turn off the fan or the light of your fanlight.

This action will open or close your electric curtain.

This action will turn your diffuser on or off.

This action will open selected curtain to the percentage you set.

This action will enable or disable the child lock.

This action will change the thermostat mode (Manual/Program).

This action will turn your eWeLink Thermostat on or off.

This action will set the light on/off or the fan speed of fanlight.

This Action will makes the camera sound an alarm.