iPhone Enters Geofence - Homeseer: If You enter an area, then run a HS system Coming Home event
Other popular HomeSeer workflows and automations
-
30
-
-
Launch HomeSeer Event When Ring Doorbell Detects Motion
-
-
Ring detect front door motion and send to homeseer
-
-
Dog House Heater ON
1
-
-
Incoming email to trigger Homeseer Event
-
-
Launch HomeSeer Event When Wyze Motion Sensor Detects Motion
-
-
Synchronize a HomeSeer virtual device with a product (in this case, a WeMo powered table lamp)
5
-
-
Launch HomeSeer Event When Ring Doorbell is Rung
1
-
-
Turn On Device When Connected
2
-
Build your own HomeSeer and Swidget automations
Triggers (If this)
-
Turned On
This trigger fires when the specified Swidget device turns on.
-
A device is turned on
This Trigger fires when a device attached to your HomeSeer system is turned on.
-
Turned Off
This trigger fires when the specified Swidget device turns off.
-
A device is turned off
This Trigger fires when a device attached to your HomeSeer system is turned off.
-
Temperature goes above
The trigger fires when the temperature goes above a given threshold.
-
Temperature goes below
This trigger fires when the temperature goes below a given value.
-
Humidity goes above
This trigger fires when the humidity goes above a given value.
-
Humidity goes below
This trigger fires when the humidity goes below a given value.
-
Motion begins
The trigger fires when motion sensor detects occupancy.
-
Motion ends
The trigger fires when motion sensor reports vacancy.
-
Air quality improves
This trigger fires when the air quality goes over a given value.
-
Air quality declines
This trigger fires when the air quality goes below a given value.
Turned On
This trigger fires when the specified Swidget device turns on.
A device is turned on
This Trigger fires when a device attached to your HomeSeer system is turned on.
Turned Off
This trigger fires when the specified Swidget device turns off.
A device is turned off
This Trigger fires when a device attached to your HomeSeer system is turned off.
Temperature goes above
The trigger fires when the temperature goes above a given threshold.
Temperature goes below
This trigger fires when the temperature goes below a given value.
Humidity goes above
This trigger fires when the humidity goes above a given value.
Humidity goes below
This trigger fires when the humidity goes below a given value.
Motion begins
The trigger fires when motion sensor detects occupancy.
Motion ends
The trigger fires when motion sensor reports vacancy.
Air quality improves
This trigger fires when the air quality goes over a given value.
Air quality declines
This trigger fires when the air quality goes below a given value.
Queries (With)
Actions (Then that)
-
Run a HomeSeer system event
This Action will run a HomeSeer system event. HomeSeer events can be programmed to control just about any combination of home automation products installed in your home!
-
Turn On
This action will turn your selected Swidget device on.
-
Turn on a device
This Action will turn on a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
-
Turn Off
This action will turn your selected Swidget device Off.
-
Turn off a device
This Action will turn off a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
-
Set Dimmer Level
This action will set your Swidget dimmer device to the specified level.
-
Dim a device
This Action will dim a dimmable lighting device attached to your HomeSeer system.
-
Lock a door lock
This Action will lock a door lock attached to your HomeSeer system.
-
Unlock a door lock
This Action will unlock a door lock attached to your HomeSeer system.
-
Change a thermostat's cool set-point
This Action will change the cool set-point of a thermostat attached to your HomeSeer system.
-
Change a thermostat's heat set-point
This Action will change the heat set-point of a thermostat attached to your HomeSeer system.
-
Change a thermostat's operating mode to auto
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to auto.
-
Change a thermostat's operating mode to off
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to off.
-
Change a thermostat's operating mode to cool
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to cool.
-
Change a thermostat's operating mode to heat
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to heat.
-
Send a text command to HomeSeer
This action will send a text command to your HomeSeer system.
Run a HomeSeer system event
This Action will run a HomeSeer system event. HomeSeer events can be programmed to control just about any combination of home automation products installed in your home!
Turn On
This action will turn your selected Swidget device on.
Turn on a device
This Action will turn on a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
Turn Off
This action will turn your selected Swidget device Off.
Turn off a device
This Action will turn off a device attached to your HomeSeer system. Devices may include light switches, receptacles, plug-in modules and much more!
Set Dimmer Level
This action will set your Swidget dimmer device to the specified level.
Dim a device
This Action will dim a dimmable lighting device attached to your HomeSeer system.
Lock a door lock
This Action will lock a door lock attached to your HomeSeer system.
Unlock a door lock
This Action will unlock a door lock attached to your HomeSeer system.
Change a thermostat's cool set-point
This Action will change the cool set-point of a thermostat attached to your HomeSeer system.
Change a thermostat's heat set-point
This Action will change the heat set-point of a thermostat attached to your HomeSeer system.
Change a thermostat's operating mode to auto
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to auto.
Change a thermostat's operating mode to off
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to off.
Change a thermostat's operating mode to cool
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to cool.
Change a thermostat's operating mode to heat
This Action will change the the operating mode of a thermostat attached to your HomeSeer system to heat.
Send a text command to HomeSeer
This action will send a text command to your HomeSeer system.
How to connect HomeSeer and Swidget
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your HomeSeer and Swidget accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together