Connect RainMachine to WeMo Maker and unlock powerful automations

This Trigger fires every time a zone has started.

This Trigger fires every time your WeMo Maker relay is turned on in toggle mode.

This Trigger fires every time a zone has stopped.

This Trigger fires every time your WeMo Maker relay is turned off in toggle mode.

This Trigger fires every time a watering program has started.

This Trigger fires every time your WeMo Maker relay is turned on in momentary mode.

This Trigger fires every time a watering program has stopped.

This Trigger fires every time a signal is detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.

This Trigger fires every time device disconnects from the remote access service.

This Trigger fires every time a signal is not detected from your sensor. NOTE: The sensor must be enabled in your Maker's settings.

This Trigger fires when device connects to the remote access service.

This Trigger fires every time a new software update is available.

This Trigger fires when freeze protect mode is in effect.

This Trigger fires every time the rain sensor detects rain.

This Trigger fires every time the rain sensor finished to detect rain.

This Trigger fires every time weather did not update for 24h

This Trigger fires every time a new weather update was successfully executed.

This Trigger fires every time a leak was detected by your sprinkler

This Trigger fires every time a reboot has occurred during watering zone or program

This Trigger fires every time an automatic firmware update has occurred.

This Trigger fires every time a snooze has become inactive.

This Trigger fires every time a snooze has become active.

This query returns a list of when your WeMo Maker relay was turned on in momentary mode.

This query returns a list of when the rain sensor detects rain.

This query returns a list of times a signal was not detected by an enabled sensor.

This query returns a list of when the watering program started.

This query returns a list of times a signal was detected by an enabled sensor.

This query returns a list of when device connected to the remote access service.

This query returns a list of when your WeMo Maker relay was turned off in toggle mode.

This query returns a list of every time a new software update is available.

This query returns a list of when your WeMo Maker relay was turned on in toggle mode.

This Action will start watering a specific zone for a certain period of time.

This Action will turn your WeMo Maker on. If the WeMo Maker is already on, it will remain on.

This Action will run a specific watering program.

This Action will turn a WeMo Maker off. If the WeMo Maker is already off, it will remain off.

This action will schedule a program to start in the next minute. The difference between scheduling a program to start and just starting a program is that scheduled program will take weather into account whereas a started program will always water 100% of the set duration

This Action will toggle a Wemo Maker if it is in toggle mode. If the relay is on, it will be turned off and vice versa.

This Action will cancel all running watering events.

This Action will turn a Wemo Maker off then on. If the WeMo Maker is already off, it will remain off.

This Action will skip all watering events for a certain period of time.

This Action will turn a WeMo Maker on then off. If the WeMo Maker is already on, it will be turned off after 2 seconds.

This Action will enable a specific program

This Action will turn a WeMo Maker on for 300 milliseconds. Note: WeMo Maker must be in 'Momentary' mode for this action to work.

This Action will disable a specific program

This Action will turn a WeMo Maker on for 300 milliseconds as many times as you set. Note: The WeMo Maker must be in 'Momentary' mode for this Action to work.

This action will change the start time for a specific program.

This Action will turn relay on then off as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.

This action will resume all watering and require beta firmware.

This Action will turn relay off then on as many times as you set. Note: The WeMo Maker must be in 'Toggle' mode for this Action to work.

This Action will pause all running watering events and require beta firmware.

This action will save weather data. Make sure you have enabled Local Weather Push from Weather > Developer > Local Weather Push. The units for the data should be metric units.

This action will change the stop time for a specific program.