This Trigger fires every time a zone has started.

This Trigger retrieves today's current weather report within 5 minutes of the time you specify. NOTE: Pollen count available only in the USA.

This Trigger fires every time a zone has stopped.

This Trigger retrieves tomorrow's weather report within 5 minutes of the time you specify, depending on when forecast data is updated.

This Trigger fires every time a watering program has started.

This Trigger monitors your local temperature and fires whenever the temperature drops below the value you provide.

This Trigger fires every time a watering program has stopped.

This Trigger monitors your local temperature and fires whenever the temperature rises above the value you provide.

This Trigger fires every time device disconnects from the remote access service.

This Trigger monitors changes in the current weather condition. When one of those conditions is met the Trigger fires. Currently only these simple conditions are supported: Rain, Snow, Cloudy, Clear.

This Trigger fires when device connects to the remote access service.

This Trigger fires every time tomorrow’s forecasted low temperature drops below a value you provide.

This Trigger fires every time a new software update is available.

This Trigger fires every time tomorrow’s forecasted high temperature rises above a value you provide.

This Trigger fires when freeze protect mode is in effect.

This Trigger monitors changes in tomorrow’s forecasted weather condition.

This Trigger fires every time the rain sensor detects rain.

This Trigger fires within 15 minutes of the sunrise in your location.

This Trigger fires every time the rain sensor finished to detect rain.

This Trigger fires within 15 minutes of the sunset in your location.

This Trigger fires every time weather did not update for 24h

This Trigger fires every time the wind speed rises above a value you specify in your location.

This Trigger fires every time a new weather update was successfully executed.

This Trigger monitors your local pollen levels and fires every time the pollen count rises above the value you specify (1-12). NOTE: Available only in the USA.

This Trigger fires every time a leak was detected by your sprinkler

This Trigger monitors your local humidity and fires every time the humidity rises above the value you specify.

This Trigger fires every time a reboot has occurred during watering zone or program

This Trigger monitors your local UV levels and fires every time the UV index rises above the value you specify (0-16).

This Trigger fires every time an automatic firmware update has occurred.

This Trigger fires every time a snooze has become inactive.

This Trigger fires every time a snooze has become active.

Get the current weather

This query returns a list of when the rain sensor detects rain.

Two day forecast

This query returns a list of when the watering program started.

This query monitors your local humidity and returns a list of times when the humidity rose above the value you specified. Note: this query will only return future events after this Applet is created.

This query returns a list of when device connected to the remote access service.

This query returns a list of times when the wind speed rose above a value you specify in your location. Note: this query will only return future events after this Applet is created.

This query returns a list of every time a new software update is available.

This query monitors your local pollen levels and returns a list of times when the pollen count rose above the value you specified (1-12). NOTE: Available only in the USA. Note: this query will only return future events after this Applet is created.

This query returns a list of times when tomorrows forecasted high temperature rose above a value you provided. Note: this query will only return future events after this Applet is created.

This query returns a list of alerts when tomorrows forecasted low temperature dropped below a value you provided. Note: this query will only return future events after this Applet is created.

This query monitors your local temperature and returns a list of times when the temperature rose above the value you provided. Note: this query will only return future events after this Applet is created.

This query monitors your local temperature and returns a list of times when the temperature dropped below the value you provide. Note: this query will only return future events after this Applet is created.

This query monitors your local UV levels and returns a list of times when the UV index rose above the value you specified (0-16). Note: this query will only return future events after this Applet is created.

This query returns a history of sunrises in your location. Note: this query will only return future events after this Applet is created.

This query returns a history of sunsets at your location.

This query returns a list of times when the observed weather changed to meet a specific condition (Rain, Snow, Cloudy, or Clear).

This query returns a list of times when the forecasted weather changed to meet a specific condition (Rain, Snow, Cloudy, or Clear).

This Action will start watering a specific zone for a certain period of time.

This Action will run a specific watering program.

This action will schedule a program to start in the next minute. The difference between scheduling a program to start and just starting a program is that scheduled program will take weather into account whereas a started program will always water 100% of the set duration

This Action will cancel all running watering events.

This Action will skip all watering events for a certain period of time.

This Action will enable a specific program

This Action will disable a specific program

This action will change the start time for a specific program.

This action will resume all watering and require beta firmware.

This Action will pause all running watering events and require beta firmware.

This action will save weather data. Make sure you have enabled Local Weather Push from Weather > Developer > Local Weather Push. The units for the data should be metric units.

This action will change the stop time for a specific program.