Precool your home before on-peak hours start
Other popular BlueLink Smart Connect workflows and automations
-
-
-
When pressing a button, turn off the system and fan
1
-
-
If the temperature outside rise above a chosen point, set the cool to chosen temperature
-
-
Decrease the heating temperature of your home during on-peak hours
-
-
When temperature drops below a certain point, start emergency heating
-
-
If the temperature outside drops below a chosen point, set the heat to chosen temperature
-
-
When You Enter an Area Change Room Temperature
-
-
Turn on Cooling and Text Me When Outside Temp Rises
-
-
Turn on the fan for two hours
-
Build your own BlueLink Smart Connect and Govee Home automations
Triggers (If this)
-
System Mode Change
This trigger fires when the system mode changes
-
Turned on/off
This trigger fires when the device is turned on/off
-
Room Temperature Drops Below
This trigger fires when the temperature in the room drops below the chosen temperature
-
Armed/DisArmed
This trigger fires when the sensor is armed or disarmed
-
Room Temperature Rises Above
This trigger fires when the temperature in the room rise above the chosen temperature
-
Contact sensor triggered
This trigger fires when contact sensor triggered
-
Room Humidity Drops Below
This trigger fires when the humidity in the room drops below the specified percentage
-
Motion sensor triggered
This trigger fires when motion sensor triggered
-
Room Humidity Rises Above
This trigger fires when the humidity in the room rises above the specified percentage
-
Water leakage detected
This trigger fires when water leakage is detected or stops
-
Fan Mode Change
This trigger fires when fan mode is changed to the specified value
-
Low battery
This trigger fires when battery is low
-
Hold Status Change
This trigger fires when the hold status of the device is changed to the specified value
-
Appliance alert
This trigger fires when the alert is triggered
-
Set Temperature Changes To Above X
This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
-
Sub-devices triggered
This trigger fires when the gateway sub device is triggered
-
Set Temperature Changes To Below X
This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
-
Low Remote Sensor Battery
This trigger fires when the remote sensor battery is low
-
Low Thermostat Battery
This trigger fires when the thermostat battery is low
-
Check Warning
This trigger fires when the check warning activates
-
UV Warning
This trigger fires when the UV warning activates
-
HUMID PADS Warning
This trigger fires when the HUMID PADS warning activates
-
Filter Warning
This trigger fires when the filter warning activates
System Mode Change
This trigger fires when the system mode changes
Turned on/off
This trigger fires when the device is turned on/off
Room Temperature Drops Below
This trigger fires when the temperature in the room drops below the chosen temperature
Armed/DisArmed
This trigger fires when the sensor is armed or disarmed
Room Temperature Rises Above
This trigger fires when the temperature in the room rise above the chosen temperature
Contact sensor triggered
This trigger fires when contact sensor triggered
Room Humidity Drops Below
This trigger fires when the humidity in the room drops below the specified percentage
Motion sensor triggered
This trigger fires when motion sensor triggered
Room Humidity Rises Above
This trigger fires when the humidity in the room rises above the specified percentage
Water leakage detected
This trigger fires when water leakage is detected or stops
Fan Mode Change
This trigger fires when fan mode is changed to the specified value
Low battery
This trigger fires when battery is low
Hold Status Change
This trigger fires when the hold status of the device is changed to the specified value
Appliance alert
This trigger fires when the alert is triggered
Set Temperature Changes To Above X
This trigger fires when you set the setpoint of either heat or cool to a temperature above a threshold specified by you
Sub-devices triggered
This trigger fires when the gateway sub device is triggered
Set Temperature Changes To Below X
This trigger fires when you set the setpoint of either heat or cool to a temperature below a threshold specified by you
Low Remote Sensor Battery
This trigger fires when the remote sensor battery is low
Low Thermostat Battery
This trigger fires when the thermostat battery is low
Check Warning
This trigger fires when the check warning activates
UV Warning
This trigger fires when the UV warning activates
HUMID PADS Warning
This trigger fires when the HUMID PADS warning activates
Filter Warning
This trigger fires when the filter warning activates
Queries (With)
Actions (Then that)
-
Set appliance mode
This action will set the device (not including lights) to a specified mode.
-
Change Room Temperature
This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
-
Arm/Disarm
You can choose to arm or disarm your device through this action.
-
Change Cool Setpoint
This action will change the current cool setpoint of the selected device.
-
Turns on/off
This action will turn on/off the device of your choosing.
-
Change Heat Setpoint
This action will change the current heat setpoint of the selected device.
-
Turn on/off Night Light
This action will turn on/off the Night Light of your choosing.
-
Change Hold Status
This action will change the current hold status of the device (either ENABLED or DISABLED)
-
Set Volume
This action will set the device Volume
-
Change System Mode
This action will change the current running mode of the device
-
Set light color
This action will set the light to specified color.
-
Change Fan Mode
This action will change the current fan mode of the device
-
Set light brightness
This action will set the light to a specified brightness.
-
Change Hold Mode
This action will change the current hold mode of the device
-
Turn on/off Warm Mist
This action will turn on/off the warm mist of the device you've chosen.
-
Turn on/off Oscillation
This action will turn on/off the oscillation of the device you've chosen.
-
Turn on/off White Noise
This action will turn on/off the white noise of the device you've chosen.
-
Turn on/off Dreamview
This action will turn on/off the Dreamview of your choosing.
-
Apply Snapshot
This action will apply the snapshot of your choice to the device that created the snapshot
-
Smart Aroma Diffuser Scenes
This action will apply the Smart Aroma Diffuser Scene of your choice to the device
Set appliance mode
This action will set the device (not including lights) to a specified mode.
Change Room Temperature
This action will change the current room temperature. Will either HEAT or COOL, based on what temperature is the thermostat is showing.
Arm/Disarm
You can choose to arm or disarm your device through this action.
Change Cool Setpoint
This action will change the current cool setpoint of the selected device.
Turns on/off
This action will turn on/off the device of your choosing.
Change Heat Setpoint
This action will change the current heat setpoint of the selected device.
Turn on/off Night Light
This action will turn on/off the Night Light of your choosing.
Change Hold Status
This action will change the current hold status of the device (either ENABLED or DISABLED)
Set Volume
This action will set the device Volume
Change System Mode
This action will change the current running mode of the device
Set light color
This action will set the light to specified color.
Change Fan Mode
This action will change the current fan mode of the device
Set light brightness
This action will set the light to a specified brightness.
Change Hold Mode
This action will change the current hold mode of the device
Turn on/off Warm Mist
This action will turn on/off the warm mist of the device you've chosen.
Turn on/off Oscillation
This action will turn on/off the oscillation of the device you've chosen.
Turn on/off White Noise
This action will turn on/off the white noise of the device you've chosen.
Turn on/off Dreamview
This action will turn on/off the Dreamview of your choosing.
Apply Snapshot
This action will apply the snapshot of your choice to the device that created the snapshot
Smart Aroma Diffuser Scenes
This action will apply the Smart Aroma Diffuser Scene of your choice to the device
How to connect BlueLink Smart Connect and Govee Home
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your BlueLink Smart Connect and Govee Home accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together