Get a phone call when measured CO₂ rises above 1000 ppm
Other popular Epion workflows and automations
-
-
-
Change device brightness on a schedule
-
-
Change light color when measured CO₂ rises above 1000 ppm
-
-
Automatically run WeMo humidifier when humidity is low
-
-
Trigger Arlo siren when measured CO₂ rises above 2000 ppm
-
-
Turn off your FIBARO connected ventilator when the CO₂ level dips above a certain level
-
-
Restore device brightness in the morning
-
-
Turn on your FIBARO connected ventilator when the CO₂ level rises above a certain level
-
-
Log high CO₂ levels in Google Sheets
-
Create your own Epion and MIYO workflow
Create custom workflows effortlessly by selecting triggers, queries, and actions. With IFTTT, it's simple: “If this” trigger happens, “then that” action follows. Streamline tasks and save time with automated workflows that work for you.
23 triggers, queries, and actions
CO₂ above a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the CO₂ level for a specific devices exceeded a specified threshold.
CO₂ below a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the CO₂ level for a specific devices becomes lower than the specified threshold.
Humidity above a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the humidity for a specific device becomes higher than the specified threshold.
Humidity below a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the humidity for a specific device becomes lower than the specified threshold.
Irrigation has started
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires if irrigation for an irrigation area has started
Irrigation has stopped
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires if irrigation has stopped for given irrigation area
Soil is dry
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires if soil is dry for given irrigation area compared to your moisture borders
Soil is wet
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires if soil is wet enough for given irrigation area compared to your moisture borders
Temperature above a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the temperature for a specific device exceeds the specified threshold.
Temperature below a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the temperature for a specific device becomes lower than the specified threshold.
History of dry soil
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when soil was dry for given irrigation area compared to your moisture borders
History of irrigation has started
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when irrigation for an area has started.
History of irrigation stops
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of if irrigation was stopped for given irrigation area
List all Epion Air
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns all your Epion Air devices.
Retrieve latest measurements
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the latest measurements of the selected Epion Air.
Activate automode
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will activate automatic irrigation for the given irrigation area.
Automower status
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
The irrigation should not start as long as the automower is still mowing. To handle this situation, MIYO can be informed if the automower has started or finished mowing.
Deactivate automode
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will deactivate automatic irrigation for given irrigation area until it is activated again. E.g. if you have a garden party you can deactivate sprinklers using this action.
Firmware update
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will check and install updates to your cube.
Send rain detected notification
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will notify MIYO if it is raining or not. This action can be used to integrate existing rain sensors into your irrigation system.
Set brightness
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will update the LED brightness for a specific device
Start irrigation
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will start irrigation for the given irrigation area.
Stop irrigation
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will stop irrigation for the given irrigation area.
Activate automode
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will activate automatic irrigation for the given irrigation area.
Automower status
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
The irrigation should not start as long as the automower is still mowing. To handle this situation, MIYO can be informed if the automower has started or finished mowing.
CO₂ above a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the CO₂ level for a specific devices exceeded a specified threshold.
CO₂ below a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the CO₂ level for a specific devices becomes lower than the specified threshold.
Deactivate automode
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will deactivate automatic irrigation for given irrigation area until it is activated again. E.g. if you have a garden party you can deactivate sprinklers using this action.
Firmware update
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will check and install updates to your cube.
History of dry soil
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when soil was dry for given irrigation area compared to your moisture borders
History of irrigation has started
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when irrigation for an area has started.
History of irrigation stops
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of if irrigation was stopped for given irrigation area
Humidity above a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the humidity for a specific device becomes higher than the specified threshold.
Humidity below a specified value
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the humidity for a specific device becomes lower than the specified threshold.
Irrigation has started
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires if irrigation for an irrigation area has started
Build an automation in seconds!
If
Select a trigger the automation will use
Then
Select an action the automation will perform
You can add delays, queries, and more actions in the next step!
GET STARTED
How to connect to a Epion automation
Find an automation using Epion
Find an automation to connect to, or create your own!Connect IFTTT to your Epion account
Securely connect the Applet services to your respective accounts.Finalize and customize your Applet
Review trigger and action settings, and click connect. Simple as that!Upgrade your automations with
-
Connect to more Applets
Connect up to 20 automations with Pro, and unlimited automations with Pro+ -
Add multiple actions with exclusive services
Add real-time data and multiple actions for smarter automations -
Get access to faster speeds
Get faster updates and more actions with higher rate limits and quicker checks
More on Epion and MIYO
About Epion
Connect your Epion Air to integrate your air quality measurements with your smart home and favorite apps.
Connect your Epion Air to integrate your air quality measurements with your smart home and favorite apps.
About MIYO
Connect MIYO, your smart irrigation system, to the services and devices you love
Connect MIYO, your smart irrigation system, to the services and devices you love