Send Me an SMS if the House is Too Hot
Other popular Gewiss Smart Home IoT workflows and automations
-
-
-
Execute a Scenario When I Leave Home
2
-
-
Send Me an SMS if the House is Too Hot
-
-
Close/Open Shutter if Winds Raise above 10 km/h
-
-
When I Leave Home, Tell me if a Light is Switched On or Off with a Telegram Message
-
-
Send me a Telegram Message When a Thermostat Reaches a Threshold
-
-
Send Me an SMS if the House is Too Cold
-
-
Stop Irrigation if Tomorrow's Forecast Calls for Rain
-
-
Execute a Scenario When I Come Back Home
-
Create your own Gewiss Smart Home IoT and Zynect Sensors workflow
Create custom workflows effortlessly by selecting triggers, queries, and actions. With IFTTT, it's simple: “If this” trigger happens, “then that” action follows. Streamline tasks and save time with automated workflows that work for you.
16 triggers, queries, and actions
Sensor battery is low
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the sensor battery is low.
Sensor is activated
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a threshold sensor detects an active condition (e.g. a leak sensor detects water).
Sensor is deactivated
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a threhsold sensor no longer detects an active condition (e.g. a leak sensor no longer detects water).
Sensor is out of range
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a sensor's value is out of bounds.
Sensor reads above
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a sensor's value is above a specified value.
Sensor reads below
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a sensor's value is below a specified value.
Something Happened With Your Thermostat
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when something happens with one of your thermostat devices.
Something Interesting Happened In The Smart Home
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when something you are interested in happens in the smart home
Get sensor data
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns data the sensor has measured.
Query the Status of a Shutter/Venetian in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a shutter or venetian in the Gewiss Smart Home.
Query the Status of Any Device in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a selected device in your smart home.
Query the Status of Any Light in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a light in the Gewiss Smart Home.
Control your Shutter or Venetian
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will move up/down or stop a shutter/venetian in your home
Execute a Scenario
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will execute a scenario available at your home
Execute Any Command
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Execute any command in your Gewiss smart home
Switch On or Off a Light
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will switch On or Off a light in your home
Control your Shutter or Venetian
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will move up/down or stop a shutter/venetian in your home
Execute a Scenario
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will execute a scenario available at your home
Execute Any Command
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Execute any command in your Gewiss smart home
Get sensor data
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns data the sensor has measured.
Query the Status of a Shutter/Venetian in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a shutter or venetian in the Gewiss Smart Home.
Query the Status of Any Device in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a selected device in your smart home.
Query the Status of Any Light in the Smart Home
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns the status of a light in the Gewiss Smart Home.
Sensor battery is low
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the sensor battery is low.
Sensor is activated
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a threshold sensor detects an active condition (e.g. a leak sensor detects water).
Sensor is deactivated
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a threhsold sensor no longer detects an active condition (e.g. a leak sensor no longer detects water).
Sensor is out of range
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a sensor's value is out of bounds.
Sensor reads above
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a sensor's value is above a specified value.
Build an automation in seconds!
If
Select a trigger the automation will use
Then
Select an action the automation will perform
You can add delays, queries, and more actions in the next step!
GET STARTED
How to connect to a Gewiss Smart Home IoT automation
Find an automation using Gewiss Smart Home IoT
Find an automation to connect to, or create your own!Connect IFTTT to your Gewiss Smart Home IoT account
Securely connect the Applet services to your respective accounts.Finalize and customize your Applet
Review trigger and action settings, and click connect. Simple as that!Upgrade your automations with
-
Connect to more Applets
Connect up to 20 automations with Pro, and unlimited automations with Pro+ -
Add multiple actions with exclusive services
Add real-time data and multiple actions for smarter automations -
Get access to faster speeds
Get faster updates and more actions with higher rate limits and quicker checks
More on Gewiss Smart Home IoT and Zynect Sensors
About Gewiss Smart Home IoT
Enhance your home automation and enjoy the well-being thanks to IFTTT.
Enhance your home automation and enjoy the well-being thanks to IFTTT.
About Zynect Sensors
Connect your Zynect Sensors to other services to take action on sensor data.
Connect your Zynect Sensors to other services to take action on sensor data.