Revert to normal schedule when you leave home
Start today
Other popular Honeywell Total Connect Comfort workflows and automations
- Increase the temperature of your Honeywell thermostat during on-peak hours
- Turn off two Honeywell thermostats when leaving home
- Set the temperature of a Honeywell Total Connect thermostat when Apilio triggers an action (2)
- Resume schedule when You return home
- Average Price Change - Honeywell - Part 2: Resume Honeywell schedule when price comes down
- Upper level AC
- If You say "Alexa trigger regular schedule", then resume programmed schedule
- Set thermostat to 75° Fahrenheit for 2 hours when you arrive home (iOS Version)
Useful Honeywell Total Connect Comfort and RainMachine integrations
Triggers (If this)
- Zone has startedThis Trigger fires every time a zone has started.
- Zone has stoppedThis Trigger fires every time a zone has stopped.
- Program has startedThis Trigger fires every time a watering program has started.
- Program has stoppedThis Trigger fires every time a watering program has stopped.
- Device is offlineThis Trigger fires every time device disconnects from the remote access service.
- Device is back onlineThis Trigger fires when device connects to the remote access service.
- New software update availableThis Trigger fires every time a new software update is available.
- Freeze Protect EnforcedThis Trigger fires when freeze protect mode is in effect.
- Rain sensor is onThis Trigger fires every time the rain sensor detects rain.
- Rain sensor is offThis Trigger fires every time the rain sensor finished to detect rain.
- No weather updateThis Trigger fires every time weather did not update for 24h
- Weather updateThis Trigger fires every time a new weather update was successfully executed.
- Leak DetectedThis Trigger fires every time a leak was detected by your sprinkler
- Reboot during wateringThis Trigger fires every time a reboot has occurred during watering zone or program
- Automatic updateThis Trigger fires every time an automatic firmware update has occurred.
- Rain delay endedThis Trigger fires every time a snooze has become inactive.
- Rain delay startedThis Trigger fires every time a snooze has become active.
Queries (With)
- History of rain sensor detects rainThis query returns a list of when the rain sensor detects rain.
- History of program startsThis query returns a list of when the watering program started.
- History of when device was back onlineThis query returns a list of when device connected to the remote access service.
- History of software updates availableThis query returns a list of every time a new software update is available.
Actions (Then that)
- Start a zoneThis Action will start watering a specific zone for a certain period of time.
- Set temperature to a permanent holdThis Action will set your Honeywell thermostat to permanently hold the specified temperature until you change it.
- Start a programThis Action will run a specific watering program.
- Set temperature for a period of timeThis Action will set your Honeywell thermostat to hold a temperature for a specified period of time. The schedule will resume when the time expires.
- Schedule a program to run in the next minuteThis action will schedule a program to start in the next minute. The difference between scheduling a program to start and just starting a program is that scheduled program will take weather into account whereas a started program will always water 100% of the set duration
- Resume programmed scheduleThis Action will set your Honeywell thermostat to resume the currently defined thermostat programmed schedule.
- Stop all wateringThis Action will cancel all running watering events.
- Set fan to on or autoThis Action will set the Honeywell thermostat fan to On where the fan is always on or Auto where the fan runs only when the heating or cooling system is on.
- SnoozeThis Action will skip all watering events for a certain period of time.
- Activate a programThis Action will enable a specific program
- Deactivate a programThis Action will disable a specific program
- Change program start timeThis action will change the start time for a specific program.
- Resume all wateringThis action will resume all watering and require beta firmware.
- Pause all wateringThis Action will pause all running watering events and require beta firmware.
- Add weather dataThis action will save weather data. Make sure you have enabled Local Weather Push from Weather > Developer > Local Weather Push. The units for the data should be metric units.
- Change stop programThis action will change the stop time for a specific program.
IFTTT helps all your apps and devices work better together