Connect Aqara Home for US to go-e Charger and unlock powerful automations

This trigger fires when the specified single rocker switch is turned on/off.

This trigger fires when charging has started.

This trigger fires when the specified double rocker switch is turned on/off.

This trigger fires when the car is plugged in.

This trigger fires when the specified triple rocker switch is turned on/off.

This trigger fires when an Error occurs.

This trigger fires when the specified Relay Controller is turned on/off.

This trigger fires when the charging process has finished.

This trigger fires when the specified light is turned on/off.

This trigger fires when charging is paused.

This trigger fires when the specified plug is turned on/off.

This trigger fires when the model status changes.

This trigger fires when the specified single rocker switch is single clicked/double clicked/long pressed.

This trigger fires when a transaction happened.

This trigger fires when the specified double rocker switch is single clicked/double clicked/long pressed.

This trigger fires when the temperature reaches the specified value.

This trigger fires when the temperature drops to the specified value.

This trigger fires when the humidity reaches the specified value.

This trigger fires when the humidity drops to the specified value.

This trigger fires when the tvoc reaches the specified value.

This trigger fires when the tvoc drops to the specified value.

This trigger fires when the darkness is detected.

This trigger fires when the specified camera detects sounds. To use this trigger, camera's sound detection should be turned on.

This trigger fires when the specified camera detects motion. To use this trigger, camera's motion detection should be turned on.

This trigger fires when motion is detected.

This trigger fires when water leak is detected.

This trigger fires when the water recedes.

This trigger fires when the door and window sensor is open.

This trigger fires when the door and window sensor is closed.

This trigger fires when the motion is detected and brightness is below the specified value.

This trigger fires when the motion is detected and brightness is above the specified value.

This trigger fires when the cube is triggered after one-minute inactivity.

This trigger fires when the the cube was flipped

This trigger fires when the cube was pushed.

This trigger fires when the cube was rotated.

This trigger fires when the cube was tapped twice.

This trigger fires when the cube was shaken.

This trigger fires when the drop is detected.

This trigger fires when the tilt is detected.

This trigger fires when the vibration is detected.

This trigger fires when the specified curtain is fully opened/closed.

This trigger fires when single press the specified switch.

This trigger fires when single press the specified switch.

The battery of the device is low

This trigger fires when When Bell ringing is detected

This trigger fires when Forcible demolition alarm detected

This trigger fires when recognize the specified face

This trigger fires when recognize strange faces

This trigger fires when somebody is lingering at your doorstep

This trigger fires when the cube flip to side 1

This trigger fires when the cube flip to side 2

This trigger fires when the cube flip to side 3

This trigger fires when the cube flip to side 4

This trigger fires when the cube flip to side 5

This trigger fires when the cube flip to side 6

This trigger fires when an event is detected in the zone

This trigger fires when the camera recognize the specified vehicle

This trigger fires when the S1E switch is clicked.

This trigger fires when presence detected.

This trigger fires when absence detected.

This trigger fires when when the camera detects pet.

This trigger fires when when the camera detects package.

This trigger fires when the camera detects detects unknown vehicle.

This trigger fires when when the camera detects human.

This query returns the amount of power from your battery.

This query returns the current temperature.

This query returns the ssid of the currently connected WiFi.

This query returns current humidity.

This query returns the friendly name of the charger.

This query returns the variant of the charger.

This query returns the current charger mode.

This query returns the grid frequency.

This query returns the automatic stop energy limit.

This query returns the flexible energy tariff price limit.

This query returns the current card id.

This query returns the total energy charged since purchase.

This query returns the temperature of the connector (type 2) and power supply.

This query returns true if an current limiting adapter (i.e. 16A) is used.

This query returns the load balancing amperes.

This query returns the force state.

This query returns the energy limit for the current charging session.

This query returns the IP address of the charger.

This query returns the firmware version.

This query returns the energy array.

This query returns the colors for Idle, Charging and Done.

This query returns the cable current limit.

This query returns the current model status.

This query returns the effective charging current.

This query returns the amount of power delivered by your pv.

This query returns the current unlock mode.

This query returns the requested current.

This query returns information about a connected WiFi.

This query returns the car state (Unknown, Idle, Wait for Car, Charging, Finished or Error).

This query returns the current state of access control setting.

This query returns the led-ring brightness

This query returns true/false, depending on if the car is allowed to charge right now.

This query returns the amount of power delivered by the power grid.

This query returns the led energy save mode.

This action will wake up the specified camera.

This action will set the charging current.

This action will sleep the specified camera.

This action will pause the charging process.

This action will wake up / sleep of the specified camera.

This action will start the charging process.

This action will enable motion detection of the specified camera.

This action will set the charging state to Neutral, Force-Off or Force-On.

This action will enable sound detection of the specified camera.

This action will reboot the charger.

This action will disable motion detection of the specified camera.

This action will set the energy limit for the current charging session.

This action will disable sound detection of the specified camera.

This action will set the mode of the charger.

This action will enable / disable motion detection of the specified camera.

This action will set the ledring brightness.

This action will enable / disable sound detection of the specified camera.

This action will set the friendly name.

This action will turn on/off the plug of your choosing.

This action will set the colors for Idle, Charging and Done.

This action will turn on/off the single rocker switches of your choosing.

This action will set the unlock mode.

This action will turn on/off the double rocker switches of your choosing.

This action will set the access control setting.

This action will turn on/off the triple rocker switches of your choosing.

This action will set the transaction setting.

This action will turn on/off the wireless relay controller of your choosing.

This action will set the led energy save mode.

This action will turn on/off the light of your choosing.

This action will set the flexible energy tariff price limit.

This action will open the curtain of your choosing.

This action will set the automatic stop energy.

This action will close the curtain of your choosing.

This action will open/close the curtain of your choosing.

This action will stop the curtain of your choosing.

This action will open the curtain of your choosing to the designated position.

This action will make feeder feed once

This action will Set the light of brightness

This action will set the color temperature of lamp

This action will set the color of the light

This action will Turn on/off the light of your choosing.

This action will run the light scenario