Resume EV Charging When Prices Drop
Start today
Triggers (If this)
Queries (With)
Actions (Then that)
Other popular go-e Charger workflows and automations
-
-
-
If Solar Charts workflow turns off, then pause charging go-e Charger
-
-
Tweet my charging session
-
-
Record transactions in google calendar
-
-
Start charging for event in google calendar
-
-
Turn on lights on charging started
-
-
Pause charging on dishwasher turned on
-
-
SMS on transaction start
-
-
Pause EV Charging When Prices Are High
-
Useful go-e Charger and TrickleStar Connected Products integrations
Triggers (If this)
-
Charging Started
This trigger fires when charging has started.
-
Thermostat mode or setpoint changes
This trigger fires when TrickleStar Thermostat system mode or setpoint changes.
-
Car connected
This trigger fires when the car is plugged in.
-
Thermostat occupancy changes
This trigger fires when TrickleStar Thermostat occupancy changes.
-
Error
This trigger fires when an Error occurs.
-
Thermostat room temperature is greater than
This trigger fires every time your TrickleStar thermostat senses that the room temperature rises above the value you specified.
-
Charging End
This trigger fires when the charging process has finished.
-
Thermostat room temperature is less than
This trigger fires every time your TrickleStar thermostat senses that the room temperature drops below the value you specified.
-
Charging Paused
This trigger fires when charging is paused.
-
WHC detects a leak
This trigger fires when TrickleStar Water Heater Controller detects a leak.
-
Model Status
This trigger fires when the model status changes.
-
Transaction
This trigger fires when a transaction happened.
Charging Started
This trigger fires when charging has started.
Thermostat mode or setpoint changes
This trigger fires when TrickleStar Thermostat system mode or setpoint changes.
Car connected
This trigger fires when the car is plugged in.
Thermostat occupancy changes
This trigger fires when TrickleStar Thermostat occupancy changes.
Error
This trigger fires when an Error occurs.
Thermostat room temperature is greater than
This trigger fires every time your TrickleStar thermostat senses that the room temperature rises above the value you specified.
Charging End
This trigger fires when the charging process has finished.
Thermostat room temperature is less than
This trigger fires every time your TrickleStar thermostat senses that the room temperature drops below the value you specified.
Charging Paused
This trigger fires when charging is paused.
WHC detects a leak
This trigger fires when TrickleStar Water Heater Controller detects a leak.
Model Status
This trigger fires when the model status changes.
Transaction
This trigger fires when a transaction happened.
Queries (With)
-
Get power from battery
This query returns the amount of power from your battery.
-
List all devices
This query returns a list of all my TrickleStar devices and their online status.
-
Currently connected WiFi ssid
This query returns the ssid of the currently connected WiFi.
-
Get Friendly Name
This query returns the friendly name of the charger.
-
Get Variant
This query returns the variant of the charger.
-
Get Mode
This query returns the current charger mode.
-
Grid Frequency
This query returns the grid frequency.
-
Get automatic stop energy
This query returns the automatic stop energy limit.
-
Get flexible energy tariff price limit
This query returns the flexible energy tariff price limit.
-
Get Transaction
This query returns the current card id.
-
Total energy
This query returns the total energy charged since purchase.
-
Get temperature
This query returns the temperature of the connector (type 2) and power supply.
-
Adapter connected
This query returns true if an current limiting adapter (i.e. 16A) is used.
-
Load Balancing Ampere
This query returns the load balancing amperes.
-
Get force state
This query returns the force state.
-
Get Energy Limit
This query returns the energy limit for the current charging session.
-
Current IP Address
This query returns the IP address of the charger.
-
Firmware Version
This query returns the firmware version.
-
Get energy Array
This query returns the energy array.
-
Get colors
This query returns the colors for Idle, Charging and Done.
-
Get cable current limit
This query returns the cable current limit.
-
Model Status
This query returns the current model status.
-
Get effective charging current
This query returns the effective charging current.
-
Get power from pv
This query returns the amount of power delivered by your pv.
-
Get unlock mode
This query returns the current unlock mode.
-
Get Requested Current
This query returns the requested current.
-
Get WiFi information
This query returns information about a connected WiFi.
-
Car State
This query returns the car state (Unknown, Idle, Wait for Car, Charging, Finished or Error).
-
Get access control
This query returns the current state of access control setting.
-
Ledring Brightness
This query returns the led-ring brightness
-
Charging Allowed
This query returns true/false, depending on if the car is allowed to charge right now.
-
Get power from powergrid
This query returns the amount of power delivered by the power grid.
-
Get led energy save mode
This query returns the led energy save mode.
Get power from battery
This query returns the amount of power from your battery.
List all devices
This query returns a list of all my TrickleStar devices and their online status.
Currently connected WiFi ssid
This query returns the ssid of the currently connected WiFi.
Get Friendly Name
This query returns the friendly name of the charger.
Get Variant
This query returns the variant of the charger.
Get Mode
This query returns the current charger mode.
Grid Frequency
This query returns the grid frequency.
Get automatic stop energy
This query returns the automatic stop energy limit.
Get flexible energy tariff price limit
This query returns the flexible energy tariff price limit.
Get Transaction
This query returns the current card id.
Total energy
This query returns the total energy charged since purchase.
Get temperature
This query returns the temperature of the connector (type 2) and power supply.
Adapter connected
This query returns true if an current limiting adapter (i.e. 16A) is used.
Load Balancing Ampere
This query returns the load balancing amperes.
Get force state
This query returns the force state.
Get Energy Limit
This query returns the energy limit for the current charging session.
Current IP Address
This query returns the IP address of the charger.
Firmware Version
This query returns the firmware version.
Get energy Array
This query returns the energy array.
Get colors
This query returns the colors for Idle, Charging and Done.
Get cable current limit
This query returns the cable current limit.
Model Status
This query returns the current model status.
Get effective charging current
This query returns the effective charging current.
Get power from pv
This query returns the amount of power delivered by your pv.
Get unlock mode
This query returns the current unlock mode.
Get Requested Current
This query returns the requested current.
Get WiFi information
This query returns information about a connected WiFi.
Car State
This query returns the car state (Unknown, Idle, Wait for Car, Charging, Finished or Error).
Get access control
This query returns the current state of access control setting.
Ledring Brightness
This query returns the led-ring brightness
Charging Allowed
This query returns true/false, depending on if the car is allowed to charge right now.
Get power from powergrid
This query returns the amount of power delivered by the power grid.
Get led energy save mode
This query returns the led energy save mode.
Actions (Then that)
-
Set Requested Current
This action will set the charging current.
-
Turn device on
This action turns on your TrickleStar Connected Product.
-
Pause charging
This action will pause the charging process.
-
Turn device off
This action turns off your TrickleStar Connected Product.
-
Start charging
This action will start the charging process.
-
Set thermostat temporary hold
This action will set temporary hold on your TrickleStar thermostat using the specified system mode and setpoint. The temporary hold will last until the next schedule event.
-
Set charging state
This action will set the charging state to Neutral, Force-Off or Force-On.
-
Resume thermostat schedule
This action will resume schedule on your TrickleStar thermostat.
-
Reboot Charger
This action will reboot the charger.
-
Set thermostat fan on
This action sets the HVAC fan on on your TrickleStar Thermostat.
-
Set Energy Limit
This action will set the energy limit for the current charging session.
-
Set thermostat fan to auto
This action sets the HVAC fan to Auto on your TrickleStar Thermostat. The Auto fan state means the fan will turn on when the HVAC system is on, and the fan will turn off when the HVAC system is off.
-
Set Mode
This action will set the mode of the charger.
-
Set thermostat fan to run once
This action turns on the HVAC fan for one run cycle, with a configurable fan run duration.
-
Set ledring brightness
This action will set the ledring brightness.
-
Schedule vacation event
This action will schedule a vacation event on all devices of the selected site. It can be used with triggers like Google Calendar "Any event starts".
-
Set Friendly Name
This action will set the friendly name.
-
Set colors
This action will set the colors for Idle, Charging and Done.
-
Set unlock mode
This action will set the unlock mode.
-
Set access control
This action will set the access control setting.
-
Set transaction
This action will set the transaction setting.
-
Set energy save mode
This action will set the led energy save mode.
-
Set flexible energy tariff price limit
This action will set the flexible energy tariff price limit.
-
Set automatic stop energy
This action will set the automatic stop energy.
Set Requested Current
This action will set the charging current.
Turn device on
This action turns on your TrickleStar Connected Product.
Pause charging
This action will pause the charging process.
Turn device off
This action turns off your TrickleStar Connected Product.
Start charging
This action will start the charging process.
Set thermostat temporary hold
This action will set temporary hold on your TrickleStar thermostat using the specified system mode and setpoint. The temporary hold will last until the next schedule event.
Set charging state
This action will set the charging state to Neutral, Force-Off or Force-On.
Resume thermostat schedule
This action will resume schedule on your TrickleStar thermostat.
Reboot Charger
This action will reboot the charger.
Set thermostat fan on
This action sets the HVAC fan on on your TrickleStar Thermostat.
Set Energy Limit
This action will set the energy limit for the current charging session.
Set thermostat fan to auto
This action sets the HVAC fan to Auto on your TrickleStar Thermostat. The Auto fan state means the fan will turn on when the HVAC system is on, and the fan will turn off when the HVAC system is off.
Set Mode
This action will set the mode of the charger.
Set thermostat fan to run once
This action turns on the HVAC fan for one run cycle, with a configurable fan run duration.
Set ledring brightness
This action will set the ledring brightness.
Schedule vacation event
This action will schedule a vacation event on all devices of the selected site. It can be used with triggers like Google Calendar "Any event starts".
Set Friendly Name
This action will set the friendly name.
Set colors
This action will set the colors for Idle, Charging and Done.
Set unlock mode
This action will set the unlock mode.
Set access control
This action will set the access control setting.
Set transaction
This action will set the transaction setting.
Set energy save mode
This action will set the led energy save mode.
Set flexible energy tariff price limit
This action will set the flexible energy tariff price limit.
Set automatic stop energy
This action will set the automatic stop energy.
IFTTT helps all your apps and devices work better together