Activate Standby Mode if the outside temperature rises above a certain level
Start today
Other popular Heatmiser workflows and automations
- If you click the Flic button, then enable Away on your Heatmiser
- When you enter a specific area set your Heatmiser Thermostat to __°
- Send an email to boost your thermostat timer
- Cancel Standby Mode on the selected Heatmiser Thermostat when Apilio triggers and action
- Adjust thermostat when you leave a specific location
- If Living Room Heatmiser has a low battery, then Set Standby Mode
- Activate Standby Mode on the selected Heatmiser Thermostat when Apilio triggers and action (6)
- Low Outside Temp Heating Boost
Useful Heatmiser and iZone integrations
Triggers (If this)
- iZone System is OffThis Trigger fires if the iZone system is turned off.
- Temperature rises aboveThis Trigger fires every time the temperature rises above a threshold you specify.
- Light is turned onThis trigger fires when an iLight is turned on.
- Temperature drops belowThis Trigger fires every time the temperature drops above a threshold you specify.
- Light is turned offThis trigger fires when an iLight is turned off.
- neoHub Away ModeThis trigger fires when your neoHub is set to away mode.
- Switch battery is lowThis trigger fires when one iLight switch battery low alarmed.
- neoHub Home ModeTriggers when your neoHub returns to Home Mode.
- iDrate system is turned onThis trigger fires when your iDrate is turned on.
- Low BatteryThis trigger fires when your Heatmiser Device has a Low Battery.
- iZone system duct temperature rises aboveThis Trigger fires if the A/C systems supply air temperature rises above a specified threshold.
- Contact Sensor ClosedThis trigger fires when the Contact Sensor is closed
- iZone system duct temperature falls belowThis Trigger fires if the iZone systems supply air temperature falls below a specified threshold.
- Contact Sensor OpenThis trigger fires when the Contact Sensor is opened
- iDrate system is turned offThis trigger fires when your iDrate is turned off.
- Zone temperature rises aboveThis Trigger fires when a zone's actual temperature rises above a specified threshold.
- iDrate controller fault detectedThis trigger fires when an iDrate controller detects a fault.
- iDrate station fault detectedThis trigger fires when an iDrate Station detects a fault.
- Zone temperature falls belowThis Trigger fires when a zone's actual temperature falls below a specified threshold.
- iZone system temperature rises aboveThis Trigger fires when the AC unit temperature rises above a specified threshold.
- iZone system temperature falls belowThis Trigger fires when the AC unit temperature falls below a specified threshold.
- iZone System is OnThis Trigger fires if the iZone system is turned on.
Queries (With)
- History of iZone system duct temperature falls belowThis query returns a list of if the iZone systems supply air temperature falls below a specified threshold. Note: this query will only return future events after this Applet is created.
- History of iDrate station fault detectedThis query returns a list of when an iDrate Station detects a fault.
- History of iLight is turned onThis query returns a list of when an iLight was turned on.
- History of iZone system is offThis query returns a list of if the iZone system was turned off.
- History of when the iDrate system turned onThis query returns a list of when your iDrate was turned on.
- History of lights turned offThis query returns a list of when an iLight was turned off.
- History of iZone System is OnThis query returns a list of when the iZone system was turned on.
- History of iZone system temperature rises aboveThis query returns a list of when the AC unit temperature rises above a specified threshold. Note: this query will only return future events after this Applet is created.
Actions (Then that)
- Turn all lights onThis action will turn all iLights on.
- Cancel temperature holdThis Action will cancel a temperature hold on the selected Heatmiser Thermostat.
- Turn all lights offThis action will turn all iLights off.
- Set temperature holdThis Action will enable a temperature hold on the selected Heatmiser Thermostat.
- Turn light onThis action will turn the specified iLight on.
- Turn neoPlug onThis Action will allow you to switch on the selected neoPlug.
- Turn light offThis action will turn the specified iLight off.
- Turn neoPlug offThis Action will turn off the selected neoPlug.
- Decrease iZone system target temperatureThis Action will decrease the A/C setpoint by the selected number of degrees celcius.
- Set TemperatureThe Action will set the temperature on the selected Heatmiser Thermostat.
- Set light brightnessChange the brightness of an iLight.
- Boost TimerThis Action will activate a Timer Boost on the selected Heatmiser Timer.
- Set zone modeThis Action will set the selected zone to selected mode
- Set Away ModeThis Action will activate Away Mode on your neoHub
- Set iSaveThis Action will set iSave for the selected iZone system. The iSave cools your whole home using your ducted reverse cycle air conditioner’s fan mode for only a few cents an hour.
- Set Home ModeThe Action will activate Home Mode on your neoHub.
- Set iZone system target temperatureThis Action will change the iZone A/C system's setpoint temperature.
- Set Standby ModeThis Action will activate Standby Mode on the selected Heatmiser Thermostat.
- Increase iZone system target temperatureThis Action will increase the A/C setpoint temperature by selected number of degrees celcius.
- Cancel Standby ModeThis Action will cancel Standby Mode on the selected Heatmiser Thermostat.
- Set zone target temperatureThis Action will change the selected zone setpoint temperature.
- Run ProfileThis action will send a stored profile to the selected thermostat.
- Increase zone target temperatureThis Action will increase the selected zone setpoint temperature by the selected number of degrees celcius.
- Run recipeThis action will run a Heatmiser Neo recipe.
- Decrease zone target temperatureThis Action will decrease the selected zone setpoint temperature by the selected number of degrees celcius.
- Set light colorThis action will change the colour of the iLight.
- Change light effectThis action will change the special effect for the iLight.
- Activate iZone favouriteThis Action will activate the selected iZone favourite.
- Activate iLight favouriteThis action will activate a specified favourite for your iLight.
- Run iDrate ProgramThis action will run the selected Program on the iDrate.
- Turn iDrate system onThis action will turn the iDrate system on.
- Turn iDrate system offThis action will turn the iDrate system off.
- Set iDrate weather modeThis action will changes the iDrate weather mode to fine.
- Run iDrate stationThis action will run the selected iDrate station.
- Set iDrate run time ratio factorThis action will change the station run times by the selected percentage. This will increase or decrease the programmed station running time.
- Turn on iZone systemThis Action will turn on the iZone system.
- Set iZone system modeThis Action will change the iZone air condition system to the selected mode.
- Set iZone system fan speedThis Action will set the iZone A/C system to the selected fan speed.
- Turn off iZone systemThis Action will turn off the iZone AC system.
- Set iZone system sleep timerThis Action will set the A/C sleep timer to a predetermined period.
IFTTT helps all your apps and devices work better together