Switch OFF Mitsubishi Clima for temperature probe
Connect top workflows
Quickly and easily enable Applets using Mitsubishi Electric kumo cloud and Vimar VIEW.-
-
-
Switch OFF Mitsubishi Clima for thermostat
-
-
Switch ON Mitsubishi Clima for temperature probe
-
-
Switch ON Mitsubishi Clima for thermostat
-
Build your own Mitsubishi Electric kumo cloud and Vimar VIEW automations
Triggers (If this)
-
Room Temperature
This trigger fires when the room temperature satisfies a condition with a threshold
-
Temperature too high
This trigger fires when a Mitsubishi Electric zone reports a room temperature above a specific threshold.
-
Room HVAC Mode
This trigger fires when occurs a variation of HVAC mode if the state satisfies a condition
-
Temperature too low
This trigger fires when a Mitsubishi Electric zone reports a room temperature below a specified threshold.
-
Room Temperature Setpoint
This trigger fires when the setpoint temperature satisfies a condition with a threshold
-
Zone turned on
This trigger fires when a Mitsubishi Electric zone turns on.
-
Temperature Sensor
This trigger fires when the temperature satisfies a condition with a threshold
-
Zone turned off
This trigger fires when a Mitsubishi Electric zone turns off.
-
Rain Amount
This trigger fires when rain amount satisfies a condition with a threshold
-
Mode changed
This trigger fires when a Mitsubishi Electric zone changes mode.
-
Wind Speed
This trigger fires when wind speed satisfies a condition with a threshold
-
Exchanged Power single phase
This trigger fires when the exchanged power satisfies a condition with a threshold
-
Produced Power single phase
This trigger fires when the produced power satisfies a condition with a threshold
-
Total Power Consumption three phases
This trigger fires when the consumed power satisfies a condition with a treshold
-
Total Power Consumption single phase
This trigger fires when the consumed power satisfies a condition with a threshold
-
Contact Interface Status
This trigger fires based on the state (on/off/changing)
Room Temperature
This trigger fires when the room temperature satisfies a condition with a threshold
Temperature too high
This trigger fires when a Mitsubishi Electric zone reports a room temperature above a specific threshold.
Room HVAC Mode
This trigger fires when occurs a variation of HVAC mode if the state satisfies a condition
Temperature too low
This trigger fires when a Mitsubishi Electric zone reports a room temperature below a specified threshold.
Room Temperature Setpoint
This trigger fires when the setpoint temperature satisfies a condition with a threshold
Zone turned on
This trigger fires when a Mitsubishi Electric zone turns on.
Temperature Sensor
This trigger fires when the temperature satisfies a condition with a threshold
Zone turned off
This trigger fires when a Mitsubishi Electric zone turns off.
Rain Amount
This trigger fires when rain amount satisfies a condition with a threshold
Mode changed
This trigger fires when a Mitsubishi Electric zone changes mode.
Wind Speed
This trigger fires when wind speed satisfies a condition with a threshold
Exchanged Power single phase
This trigger fires when the exchanged power satisfies a condition with a threshold
Produced Power single phase
This trigger fires when the produced power satisfies a condition with a threshold
Total Power Consumption three phases
This trigger fires when the consumed power satisfies a condition with a treshold
Total Power Consumption single phase
This trigger fires when the consumed power satisfies a condition with a threshold
Contact Interface Status
This trigger fires based on the state (on/off/changing)
Queries (With)
Actions (Then that)
-
Light control
Turn on/off a light
-
Turn on
This action will turn on a Mitsubishi Electric zone and optionally change the mode.
-
Brightness control
Set brightness of a light
-
Turn off
This action will turn off a Mitsubishi Electric zone.
-
Light's color
Change the color of a light
-
Lower temperature
This action will lower the target temperature of a Mitsubishi Electric zone.
-
Scenario
Activate a scenario
-
Raise temperature
This action will raise the target temperature of a Mitsubishi Electric zone.
-
Roller shutter control
Move up / down a roller shutter
-
Roller shutter position
Set the position of a roller shutter
-
Temperature control
Change the temperature setpoint
-
Climate control
Change the climate mode
-
Automation control
Turn on/off an automation element
Light control
Turn on/off a light
Turn on
This action will turn on a Mitsubishi Electric zone and optionally change the mode.
Brightness control
Set brightness of a light
Turn off
This action will turn off a Mitsubishi Electric zone.
Light's color
Change the color of a light
Lower temperature
This action will lower the target temperature of a Mitsubishi Electric zone.
Scenario
Activate a scenario
Raise temperature
This action will raise the target temperature of a Mitsubishi Electric zone.
Roller shutter control
Move up / down a roller shutter
Roller shutter position
Set the position of a roller shutter
Temperature control
Change the temperature setpoint
Climate control
Change the climate mode
Automation control
Turn on/off an automation element
How to connect Mitsubishi Electric kumo cloud and Vimar VIEW
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your Mitsubishi Electric kumo cloud and Vimar VIEW accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together