Get an email when Mitsubishi Electric temperature drops too low
How this automation works
This applet automatically turns off your selected Mitsubishi Electric zone when the Vimar VIEW temperature sensor detects that the measured temperature surpasses your set threshold. It helps prevent overcooling or overheating, keeping your environment energy-efficient. For example, if the room warms up beyond your comfort level, the system switches off automatically to save energy.
If
Trigger ingredients
CreatedAt
Device
State
Then
Action fields
serial
Services used in this Applet
You might also like...
-
1.02K
-
-
Get an email alert when Mitsubishi Electric temperature is too high
818
-
-
Receive Email When Zone Is Deactivated
383
-
Related services
Create your own Vimar VIEW and Mitsubishi Electric kumo cloud workflow
Create custom workflows effortlessly by selecting triggers, queries, and actions. With IFTTT, it's simple: “If this” trigger happens, “then that” action follows. Streamline tasks and save time with automated workflows that work for you.
32 triggers, queries, and actions
Access Interface Status
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires based on the state (open/closed/changing)
Contact Interface Status
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires based on the state (on/off/changing)
Exchanged Power single phase
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the exchanged power satisfies a condition with a threshold
Mode changed
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a Mitsubishi Electric zone changes mode.
Presence Detection
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the presence detector change his state
Produced Power single phase
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the produced power satisfies a condition with a threshold
Rain Amount
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when rain amount satisfies a condition with a threshold
Room HVAC Mode
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when occurs a variation of HVAC mode if the state satisfies a condition
Room Temperature
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the room temperature satisfies a condition with a threshold
Room Temperature Setpoint
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the setpoint temperature satisfies a condition with a threshold
Temperature Sensor
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the temperature satisfies a condition with a threshold
Temperature too high
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a Mitsubishi Electric zone reports a room temperature above a specific threshold.
History of zone being turned off
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when a Mitsubishi Electric zone was turned off.
Automation control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Turn on/off an automation element
Brightness control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Set brightness of a light
Light control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Turn on/off a light
Light's color
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Change the color of a light
Lower temperature
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will lower the target temperature of a Mitsubishi Electric zone.
Raise temperature
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will raise the target temperature of a Mitsubishi Electric zone.
Roller shutter control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Move up / down a roller shutter
Roller shutter position
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Set the position of a roller shutter
Room HVAC Mode
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Change the Room HVAC Mode
Room Temperature Setpoint
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Change the Room Temperature Setpoint
Scenario
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Activate a scenario
Turn off
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will turn off a Mitsubishi Electric zone.
Access Interface Status
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires based on the state (open/closed/changing)
Automation control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Turn on/off an automation element
Brightness control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Set brightness of a light
Contact Interface Status
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires based on the state (on/off/changing)
Exchanged Power single phase
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the exchanged power satisfies a condition with a threshold
History of zone being turned off
Query
A query lets your Applet retrieve extra data that isn't included in the trigger, so that your automation can include more complete or useful information.
This query returns a list of when a Mitsubishi Electric zone was turned off.
Light control
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Turn on/off a light
Light's color
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
Change the color of a light
Lower temperature
Action
An action is the task your Applet carries out after the trigger occurs. It defines what happens as the result of your automation and completes the workflow.
This action will lower the target temperature of a Mitsubishi Electric zone.
Mode changed
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when a Mitsubishi Electric zone changes mode.
Presence Detection
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the presence detector change his state
Produced Power single phase
Polling trigger
Polling Applets run after IFTTT reaches out to the trigger service and finds a new trigger event. These trigger checks occur every 5 minutes for Pro and Pro+ users, and every hour for Free users.
This trigger fires when the produced power satisfies a condition with a threshold
Build an automation in seconds!
If
Select a trigger the automation will use
Then
Select an action the automation will perform
You can add delays, queries, and more actions in the next step!
More on Vimar VIEW and Mitsubishi Electric kumo cloud
About Vimar VIEW
Personalize your home with Vimar VIEW: control your connected devices thanks to IFTTT.
Personalize your home with Vimar VIEW: control your connected devices thanks to IFTTT.
About Mitsubishi Electric kumo cloud
kumo cloud gives you the ability to effortlessly control your home’s comfort. Whether you’re out for the day or the month, whether you want to cool down, or warm up, kumo cloud gives you control from any smartphone or tablet.
kumo cloud gives you the ability to effortlessly control your home’s comfort. Whether you’re out for the day or the month, whether you want to cool down, or warm up, kumo cloud gives you control from any smartphone or tablet.