Dim lights when heating is turned on
Other popular LightwaveRF Heating workflows and automations
-
-
-
Set thermostat temperature every morning
-
-
Switch on heating every night
-
-
Turn a LightwaveRF Electric Switch off when you leave home
5
-
-
Fully open a LightwaveRF TRV when the temperature gets cold
7
-
-
Fully open a LightwaveRF TRV when the temperature gets cold
13
-
-
Lower your house target temperature when it gets warm
22
-
-
Turn my heating up when I get near my home
17
-
-
Get an email when LightwaveRF Heating publishes a new trigger or action
33
-
Build your own LightwaveRF Heating and Vimar VIEW automations
Triggers (If this)
-
Room Temperature
This trigger fires when the room temperature satisfies a condition with a threshold
-
Heat turned off
This trigger fires when a thermostat device deactivates
-
Room HVAC Mode
This trigger fires when occurs a variation of HVAC mode if the state satisfies a condition
-
Temperature below target
This trigger fires when the temperature falls below the set target.
-
Room Temperature Setpoint
This trigger fires when the setpoint temperature satisfies a condition with a threshold
-
Temperature above target
This trigger fires when the temperature rises above the set target.
-
Temperature Sensor
This trigger fires when the temperature satisfies a condition with a threshold
-
Heat turned on
This trigger fires when a thermostat device activates
-
Rain Amount
This trigger fires when rain amount satisfies a condition with a threshold
-
Wind Speed
This trigger fires when wind speed satisfies a condition with a threshold
-
Exchanged Power single phase
This trigger fires when the exchanged power satisfies a condition with a threshold
-
Produced Power single phase
This trigger fires when the produced power satisfies a condition with a threshold
-
Total Power Consumption three phases
This trigger fires when the consumed power satisfies a condition with a treshold
-
Total Power Consumption single phase
This trigger fires when the consumed power satisfies a condition with a threshold
-
Contact Interface Status
This trigger fires based on the state (on/off/changing)
Room Temperature
This trigger fires when the room temperature satisfies a condition with a threshold
Heat turned off
This trigger fires when a thermostat device deactivates
Room HVAC Mode
This trigger fires when occurs a variation of HVAC mode if the state satisfies a condition
Temperature below target
This trigger fires when the temperature falls below the set target.
Room Temperature Setpoint
This trigger fires when the setpoint temperature satisfies a condition with a threshold
Temperature above target
This trigger fires when the temperature rises above the set target.
Temperature Sensor
This trigger fires when the temperature satisfies a condition with a threshold
Heat turned on
This trigger fires when a thermostat device activates
Rain Amount
This trigger fires when rain amount satisfies a condition with a threshold
Wind Speed
This trigger fires when wind speed satisfies a condition with a threshold
Exchanged Power single phase
This trigger fires when the exchanged power satisfies a condition with a threshold
Produced Power single phase
This trigger fires when the produced power satisfies a condition with a threshold
Total Power Consumption three phases
This trigger fires when the consumed power satisfies a condition with a treshold
Total Power Consumption single phase
This trigger fires when the consumed power satisfies a condition with a threshold
Contact Interface Status
This trigger fires based on the state (on/off/changing)
Actions (Then that)
-
Set temperature
This Action will set the temperature of a thermostat or thermostatic radiator valve (TRV).
-
Light control
Turn on/off a light
-
Electric Switch On
This Action will switch the Electric Switch On.
-
Brightness control
Set brightness of a light
-
Electric Switch Off
This Action will switch the Electric Switch Off.
-
Light's color
Change the color of a light
-
Set TRV Position 0
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Scenario
Activate a scenario
-
Set TRV Position 1
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Roller shutter control
Move up / down a roller shutter
-
Set TRV Position 2
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Roller shutter position
Set the position of a roller shutter
-
Set TRV Position 3
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Temperature control
Change the temperature setpoint
-
Set TRV Position 4
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Climate control
Change the climate mode
-
Set TRV Position 5
This Action will set the position of a Thermostatic Radiator Valve (TRV).
-
Automation control
Turn on/off an automation element
-
Set TRV to a Position
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Set temperature
This Action will set the temperature of a thermostat or thermostatic radiator valve (TRV).
Light control
Turn on/off a light
Electric Switch On
This Action will switch the Electric Switch On.
Brightness control
Set brightness of a light
Electric Switch Off
This Action will switch the Electric Switch Off.
Light's color
Change the color of a light
Set TRV Position 0
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Scenario
Activate a scenario
Set TRV Position 1
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Roller shutter control
Move up / down a roller shutter
Set TRV Position 2
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Roller shutter position
Set the position of a roller shutter
Set TRV Position 3
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Temperature control
Change the temperature setpoint
Set TRV Position 4
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Climate control
Change the climate mode
Set TRV Position 5
This Action will set the position of a Thermostatic Radiator Valve (TRV).
Automation control
Turn on/off an automation element
Set TRV to a Position
This Action will set the position of a Thermostatic Radiator Valve (TRV).
How to connect LightwaveRF Heating and Vimar VIEW
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your LightwaveRF Heating and Vimar VIEW accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together