When I leave home in location, run a scene in domovea
Start today
Other popular domovea workflows and automations
- Switch off a SmartThings device with domovea
- When I get close to the home in location, run a scene in domovea
- Launch a sequence when device is switched on
- When Logitech Pop is pressed, turn on a light in domovea
- Switch on a domovea device with SmartThings
- When the alarm rings in domovea, send me a sms
- When CO2 level in domovea is too high, turn on the samsung air purifier
- When domovea run the scene I am leaving, turn off the Tado thermostat
Useful domovea and RainMachine integrations
Triggers (If this)
- Device is switched onThis Trigger fires every time your device is switched on.
- Zone has startedThis Trigger fires every time a zone has started.
- Device is switched offThis Trigger fires every time your device is switched off.
- Zone has stoppedThis Trigger fires every time a zone has stopped.
- Security System is armedThis Trigger fires every time your Security system is armed.
- Program has startedThis Trigger fires every time a watering program has started.
- Security System is disarmedThis Trigger fires every time your security system is disarmed.
- Program has stoppedThis Trigger fires every time a watering program has stopped.
- Intrusion is detectedThis Trigger fires every time an intrusion is detected by your security system.
- Device is offlineThis Trigger fires every time device disconnects from the remote access service.
- Indoor temperature rises aboveThis Trigger fires every time your device detects room temperature above the value you specified.
- Device is back onlineThis Trigger fires when device connects to the remote access service.
- Indoor temperature drops belowThis Trigger fires every time your device detects indoor temperature below the value you specified.
- New software update availableThis Trigger fires every time a new software update is available.
- Shades are openedThis Trigger fires every time your shades are opened.
- Freeze Protect EnforcedThis Trigger fires when freeze protect mode is in effect.
- Shades are closedThis Trigger fires every time your shades are closed.
- Rain sensor is onThis Trigger fires every time the rain sensor detects rain.
- Thermostat temperature is equal to __°CThis Trigger fires every time your thermostat reaches the temperature you specified.
- Rain sensor is offThis Trigger fires every time the rain sensor finished to detect rain.
- Scene is launchedThis Trigger fires every time a scene is launched.
- No weather updateThis Trigger fires every time weather did not update for 24h
- Wind speed is __km/hThis Trigger fires every time the wind speed is equal to the value you specified.
- Weather updateThis Trigger fires every time a new weather update was successfully executed.
- CO2 is __ ppmThis Trigger fires every time when the CO2 is equal to the ppm you specified.
- Leak DetectedThis Trigger fires every time a leak was detected by your sprinkler
- Indoor humidity is __%This Trigger fires every time when the indoor humidity is equal to the percentage you specified.
- Reboot during wateringThis Trigger fires every time a reboot has occurred during watering zone or program
- Luminosity is __luxThis Trigger fires every time when the luminosity is equal to the value you specified.
- Automatic updateThis Trigger fires every time an automatic firmware update has occurred.
- Brightness is __%This Trigger fires every time when the brightness is equal to the value you specified.
- Rain delay endedThis Trigger fires every time a snooze has become inactive.
- It is rainingThis Trigger fires every time when it is raining.
- Rain delay startedThis Trigger fires every time a snooze has become active.
- Outdoor temperature is __°CThis Trigger fires every time when the outdoor temperature is equal to the value you specified.
- Indoor temperature is __°CThis Trigger fires every time when the indoor temperature is equal to the value you specified.
- Outdoor humidity is __%This Trigger fires every time when the outdoor humidity is equal to the percentage you specified.
- Smoke alarm ringsThis Trigger fires every time when the smoke alarm goes off.
Queries (With)
- History of outdoor temperature at a specified value in celciusThis query returns a list of recent times when the outdoor temperature was at a specified value in celcius.
- History of rain sensor detects rainThis query returns a list of when the rain sensor detects rain.
- History of CO2 at a specified ppm levelThis query returns a list of when CO2 is recorded at a specified ppm.
- History of program startsThis query returns a list of when the watering program started.
- History of security system disarmsThis query returns a list of when your security system was disarmed.
- History of when device was back onlineThis query returns a list of when device connected to the remote access service.
- History of shades opensThis query returns a list of when your shades are opened.
- History of software updates availableThis query returns a list of every time a new software update is available.
- History of indoor temperature dropping below specified valueThis query returns a list of when your device detected indoor temperature to be below the value that you specified. Note: this query will only return future events after this Applet is created.
- History of recent "Brightness is __%" alertsThis query returns a list of recent alerts when the brightness was equal to the value you specified.
Actions (Then that)
- Switch onThis Action will turn on your devices that support switching on.
- Start a zoneThis Action will start watering a specific zone for a certain period of time.
- Switch offThis Action will turn off your devices that support switching off.
- Start a programThis Action will run a specific watering program.
- Open ShadeThis action will open the shade
- Schedule a program to run in the next minuteThis action will schedule a program to start in the next minute. The difference between scheduling a program to start and just starting a program is that scheduled program will take weather into account whereas a started program will always water 100% of the set duration
- Close ShadeThis action will close the shade
- Stop all wateringThis Action will cancel all running watering events.
- Set shade position to __ %This Action will set the shade to the position you specify.
- SnoozeThis Action will skip all watering events for a certain period of time.
- Set intensity to __%This Action will set intensity to the percentage you specified.
- Activate a programThis Action will enable a specific program
- Set the thermostat modeThis Action will set the thermostat to the mode you specified.
- Deactivate a programThis Action will disable a specific program
- Set the thermostat temperature setpointThis Action will set the thermostat temperature setpoint to the value you specified.
- Change program start timeThis action will change the start time for a specific program.
- Play an audio tuneThis Action will play an audio tune.
- Resume all wateringThis action will resume all watering and require beta firmware.
- Pause an audio tuneThis action will pause an audio tune.
- Pause all wateringThis Action will pause all running watering events and require beta firmware.
- Override hot waterThis action will override the hot water.
- Add weather dataThis action will save weather data. Make sure you have enabled Local Weather Push from Weather > Developer > Local Weather Push. The units for the data should be metric units.
- Exempt hot waterThis action will exempt hot water.
- Change stop programThis action will change the stop time for a specific program.
- Run sceneThis Action will run a scene.
IFTTT helps all your apps and devices work better together