If you exit an area (iOS), then set zone temperature to X°
Start today
Other popular Honeywell Single-zone Thermostat workflows and automations
- If you exit an area, then disable a quick action
- If new SMS sent matches "Quickaction", then enable a quick action
- If you enter an area (iOS), then set a zone temperature to X°
- Wi-Fi termostat trigger
- If every day at 05:15 PM, then disable a quick action
- If You enter an area, then set a zone temperature
- Disable quick action
- If sunrise, then set a zone temperature
Useful Honeywell Single-zone Thermostat and iZone integrations
Triggers (If this)
- iZone System is OffThis Trigger fires if the iZone system is turned off.
- Light is turned onThis trigger fires when an iLight is turned on.
- Light is turned offThis trigger fires when an iLight is turned off.
- Switch battery is lowThis trigger fires when one iLight switch battery low alarmed.
- iDrate system is turned onThis trigger fires when your iDrate is turned on.
- iZone system duct temperature rises aboveThis Trigger fires if the A/C systems supply air temperature rises above a specified threshold.
- iZone system duct temperature falls belowThis Trigger fires if the iZone systems supply air temperature falls below a specified threshold.
- iDrate system is turned offThis trigger fires when your iDrate is turned off.
- Zone temperature rises aboveThis Trigger fires when a zone's actual temperature rises above a specified threshold.
- iDrate controller fault detectedThis trigger fires when an iDrate controller detects a fault.
- iDrate station fault detectedThis trigger fires when an iDrate Station detects a fault.
- Zone temperature falls belowThis Trigger fires when a zone's actual temperature falls below a specified threshold.
- iZone system temperature rises aboveThis Trigger fires when the AC unit temperature rises above a specified threshold.
- iZone system temperature falls belowThis Trigger fires when the AC unit temperature falls below a specified threshold.
- iZone System is OnThis Trigger fires if the iZone system is turned on.
Queries (With)
- History of iZone system duct temperature falls belowThis query returns a list of if the iZone systems supply air temperature falls below a specified threshold. Note: this query will only return future events after this Applet is created.
- History of iDrate station fault detectedThis query returns a list of when an iDrate Station detects a fault.
- History of iLight is turned onThis query returns a list of when an iLight was turned on.
- History of iZone system is offThis query returns a list of if the iZone system was turned off.
- History of when the iDrate system turned onThis query returns a list of when your iDrate was turned on.
- History of lights turned offThis query returns a list of when an iLight was turned off.
- History of iZone System is OnThis query returns a list of when the iZone system was turned on.
- History of iZone system temperature rises aboveThis query returns a list of when the AC unit temperature rises above a specified threshold. Note: this query will only return future events after this Applet is created.
Actions (Then that)
- Turn all lights onThis action will turn all iLights on.
- Enable quick actionThis action will enable a quick action at one of your locations. This can either be permanent or for a number of days/hours.
- Turn all lights offThis action will turn all iLights off.
- Disable a quick actionThis action will remove any existing quick action at your location and set your heating system to follow the schedule.
- Turn light onThis action will turn the specified iLight on.
- Set a zone temperatureThis action sets an override on target temperature of one of your zones. This can either be permanently set or just for a number of hours.
- Turn light offThis action will turn the specified iLight off.
- Decrease iZone system target temperatureThis Action will decrease the A/C setpoint by the selected number of degrees celcius.
- Set light brightnessChange the brightness of an iLight.
- Set zone modeThis Action will set the selected zone to selected mode
- Set iSaveThis Action will set iSave for the selected iZone system. The iSave cools your whole home using your ducted reverse cycle air conditioner’s fan mode for only a few cents an hour.
- Set iZone system target temperatureThis Action will change the iZone A/C system's setpoint temperature.
- Increase iZone system target temperatureThis Action will increase the A/C setpoint temperature by selected number of degrees celcius.
- Set zone target temperatureThis Action will change the selected zone setpoint temperature.
- Increase zone target temperatureThis Action will increase the selected zone setpoint temperature by the selected number of degrees celcius.
- Decrease zone target temperatureThis Action will decrease the selected zone setpoint temperature by the selected number of degrees celcius.
- Set light colorThis action will change the colour of the iLight.
- Change light effectThis action will change the special effect for the iLight.
- Activate iZone favouriteThis Action will activate the selected iZone favourite.
- Activate iLight favouriteThis action will activate a specified favourite for your iLight.
- Run iDrate ProgramThis action will run the selected Program on the iDrate.
- Turn iDrate system onThis action will turn the iDrate system on.
- Turn iDrate system offThis action will turn the iDrate system off.
- Set iDrate weather modeThis action will changes the iDrate weather mode to fine.
- Run iDrate stationThis action will run the selected iDrate station.
- Set iDrate run time ratio factorThis action will change the station run times by the selected percentage. This will increase or decrease the programmed station running time.
- Turn on iZone systemThis Action will turn on the iZone system.
- Set iZone system modeThis Action will change the iZone air condition system to the selected mode.
- Set iZone system fan speedThis Action will set the iZone A/C system to the selected fan speed.
- Turn off iZone systemThis Action will turn off the iZone AC system.
- Set iZone system sleep timerThis Action will set the A/C sleep timer to a predetermined period.
IFTTT helps all your apps and devices work better together