If every day at 05:15 PM, then disable a quick action
Other popular Honeywell Single-zone Thermostat workflows and automations
-
-
-
If new SMS sent matches "Quickaction", then enable a quick action
-
-
Disable quick action
3
-
-
Wi-Fi termostat trigger
1
-
-
Get an email when Honeywell Single-zone Thermostat publishes a new trigger or action
25
-
-
Set a thermostat zone temperature
16
-
-
Adjust bedroom temperature when Sleep recording starts
-
-
Set a zone temperature
19
-
-
If outside temperature drops below X°, then disable quick actions and go back to schedule
6
-
Build your own Honeywell Single-zone Thermostat and MIYO automations
Triggers (If this)
-
Irrigation has started
This trigger fires if irrigation for an irrigation area has started
-
Irrigation has stopped
This trigger fires if irrigation has stopped for given irrigation area
-
Soil is dry
This trigger fires if soil is dry for given irrigation area compared to your moisture borders
-
Soil is wet
This trigger fires if soil is wet enough for given irrigation area compared to your moisture borders
Irrigation has started
This trigger fires if irrigation for an irrigation area has started
Irrigation has stopped
This trigger fires if irrigation has stopped for given irrigation area
Soil is dry
This trigger fires if soil is dry for given irrigation area compared to your moisture borders
Soil is wet
This trigger fires if soil is wet enough for given irrigation area compared to your moisture borders
Queries (With)
-
History of irrigation has started
This query returns a list of when irrigation for an area has started.
-
History of dry soil
This query returns a list of when soil was dry for given irrigation area compared to your moisture borders
-
History of irrigation stops
This query returns a list of if irrigation was stopped for given irrigation area
History of irrigation has started
This query returns a list of when irrigation for an area has started.
History of dry soil
This query returns a list of when soil was dry for given irrigation area compared to your moisture borders
History of irrigation stops
This query returns a list of if irrigation was stopped for given irrigation area
Actions (Then that)
-
Start irrigation
This action will start irrigation for the given irrigation area.
-
Enable quick action
This action will enable a quick action at one of your locations. This can either be permanent or for a number of days/hours.
-
Stop irrigation
This action will stop irrigation for the given irrigation area.
-
Disable a quick action
This action will remove any existing quick action at your location and set your heating system to follow the schedule.
-
Activate automode
This action will activate automatic irrigation for the given irrigation area.
-
Set a zone temperature
This action sets an override on target temperature of one of your zones. This can either be permanently set or just for a number of hours.
-
Deactivate automode
This action will deactivate automatic irrigation for given irrigation area until it is activated again. E.g. if you have a garden party you can deactivate sprinklers using this action.
-
Send rain detected notification
This action will notify MIYO if it is raining or not. This action can be used to integrate existing rain sensors into your irrigation system.
-
Firmware update
This action will check and install updates to your cube.
-
Automower status
The irrigation should not start as long as the automower is still mowing. To handle this situation, MIYO can be informed if the automower has started or finished mowing.
Start irrigation
This action will start irrigation for the given irrigation area.
Enable quick action
This action will enable a quick action at one of your locations. This can either be permanent or for a number of days/hours.
Stop irrigation
This action will stop irrigation for the given irrigation area.
Disable a quick action
This action will remove any existing quick action at your location and set your heating system to follow the schedule.
Activate automode
This action will activate automatic irrigation for the given irrigation area.
Set a zone temperature
This action sets an override on target temperature of one of your zones. This can either be permanently set or just for a number of hours.
Deactivate automode
This action will deactivate automatic irrigation for given irrigation area until it is activated again. E.g. if you have a garden party you can deactivate sprinklers using this action.
Send rain detected notification
This action will notify MIYO if it is raining or not. This action can be used to integrate existing rain sensors into your irrigation system.
Firmware update
This action will check and install updates to your cube.
Automower status
The irrigation should not start as long as the automower is still mowing. To handle this situation, MIYO can be informed if the automower has started or finished mowing.
How to connect Honeywell Single-zone Thermostat and MIYO
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your Honeywell Single-zone Thermostat and MIYO accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together